Browsing by Subject "Polyethylene oxides"
Now showing 1 - 5 of 5
Results Per Page
Sort Options
Item Open Access Bacteria encapsulated electrospun nanofibrous webs for remediation of methylene blue dye in water(Elsevier, 2017-04) Sarioglu O.F.; Keskin, N. O. S.; Celebioglu A.; Tekinay, T.; Uyar, TamerIn this study, preparation and application of novel biocomposite materials that were produced by encapsulation of bacterial cells within electrospun nanofibrous webs are described. A commercial strain of Pseudomonas aeruginosa which has methylene blue (MB) dye remediation capability was selected for encapsulation, and polyvinyl alcohol (PVA) and polyethylene oxide (PEO) were selected as the polymer matrices for the electrospinning of bacteria encapsulated nanofibrous webs. Encapsulation of bacterial cells was monitored by scanning electron microscopy (SEM) and fluorescence microscopy, and the viability of encapsulated bacteria was checked by live/dead staining and viable cell counting assay. Both bacteria/PVA and bacteria/PEO webs have shown a great potential for remediation of MB, yet bacteria/PEO web has shown higher removal performances than bacteria/PVA web, which was probably due to the differences in the initial viable bacterial cells for those two samples. The bacteria encapsulated electrospun nanofibrous webs were stored at 4 °C for three months and they were found as potentially storable for keeping encapsulated bacterial cells alive. Overall, the results suggest that electrospun nanofibrous webs are suitable platforms for preservation of living bacterial cells and they can be used directly as a starting inoculum for bioremediation of water systems.Item Open Access Continuous mesoporous pd films by electrochemical deposition in nonionic micellar solution(American Chemical Society, 2017) Iqbal, M.; Li C.; Wood, K.; Jiang B.; Takei, T.; Dag, Ö.; Baba, D.; Nugraha, A. S.; Asahi, T.; Whitten, A. E.; Hossain, M. S. A.; Malgras, V.; Yamauchi, Y.Mesoporous metals that combine catalytic activity and high surface area can provide more opportunities for electrochemical applications. Various synthetic methods, including hard and soft templating, have been developed to prepare mesoporous/nanoporous metals. Micelle assembly, typically involved in soft-templates, is flexible and convenient for such purposes. It is, however, difficult to control, and the ordering is significantly destroyed during the metal deposition process, which is detrimental when it comes to designing precisely mesostructured materials. In the present work, mesoporous Pd films were uniformly electrodeposited using a nonionic surfactant, triblock copolymer poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide), as a pore-directing agent. The interaction between micelles and metal precursors greatly influences the metal growth and determines the final structure. The water-coordinated species interact with the ethylene oxide moiety of the micelles to effectively drive the Pd(II) species toward the working electrode surface. From small-angle neutron scattering data, it is found that spherical P123 micelles, with an average diameter of ∼14 nm, are formed in the electrolyte, and the addition of Pd ions does not significantly modify their structure, which is the essence of the micelle assembly approach. The uniformly sized mesopores are formed over the entire mesoporous Pd film and have an average pore diameter of 10.9 nm. Cross-sectional observation of the film also shows mesopores spanning continuously from the bottom to the top of the film. The crystallinity, crystal phase, and electronic coordination state of the Pd film are also confirmed. Through this study, it is found that the optimized surfactant concentration and applied deposition potential are the key factors to govern the formation of homogeneous and well-distributed pores over the entire film. Interestingly, the as-prepared mesoporous Pd films exhibit superior electrocatalytic activity toward the ethanol oxidation reaction by fully utilizing the accessible active surface area. Our approach combines electrochemistry with colloidal and coordination chemistry and is widely applicable to other promising metals and alloy electrocatalysts.Item Open Access In situ synthesis of biomolecule encapsulated gold-cross-linked poly(ethylene glycol) nanocomposite as biosensing platform: A model study(Elsevier BV, 2010) Odaci, D.; Kahveci, M.U.; Sahkulubey, E.L.; Ozdemir, C.; Uyar, Tamer; Timur, S.; Yagci Y.In situ synthesis of poly(ethylene glycol) (PEG) hydrogels containing gold nanoparticles(AuNPs) and glucose oxidase (GOx) enzyme by photo-induced electron transfer process was reported here and applied in electrochemical glucose biosensing as the model system. Newly designed bionanocomposite matrix by simple one-step fabrication offered a good contact between the active site of the enzyme and AuNPs inside the network that caused the promotion in the electron transfer properties that was evidenced by cyclic voltammetryas well as higher amperometric biosensing responses in comparing with response signals obtained from the matrix without AuNPs. As well as some parameters important in the optimization studies such as optimum pH, enzyme loading and AuNP amount, the analytical characteristics of the biosensor (AuNP/GOx) were examined by the monitoring of chronoamperometric response due to the oxygen consumption through the enzymatic reaction at − 0.7 V under optimized conditions at sodium acetate buffer (50 mM, pH 4.0) and the linear graph was obtained in the range of 0.1–1.0 mM glucose. The detection limit (LOD) of the biosensor was calculated as 0.06 mM by using the signal to noise ratio of 3. Moreover, the presence of AuNPs was visualized by TEM. Finally, the biosensor was applied for glucose analysis for some beverages and obtained data were compared with HPLC as the reference method to test the possible matrix effect due to the nature of the samples.Item Open Access In vitro biocompatibility of plasma-aided surface-modified 316L stainless steel for intracoronary stents(Institute of Physics Publishing, 2010) Bayram, C.; Mizrak, A.K.; Aktürk, S.; Kurşaklioǧlu H.; Iyisoy, A.; Ifran, A.; Denkbaş, E.B.316L-type stainless steel is a raw material mostly used for manufacturing metallic coronary stents. The purpose of this study was to examine the chemical, wettability, cytotoxic and haemocompatibility properties of 316L stainless steel stents which were modified by plasma polymerization. Six different polymeric compounds, polyethylene glycol, 2-hydroxyethyl methacrylate, ethylenediamine, acrylic acid, hexamethyldisilane and hexamethyldisiloxane, were used in a radio frequency glow discharge plasma polymerization system. As a model antiproliferative drug, mitomycin-C was chosen for covalent coupling onto the stent surface. Modified SS 316L stents were characterized by water contact angle measurements (goniometer) and x-ray photoelectron spectroscopy. C1s binding energies showed a good correlation with the literature. Haemocompatibility tests of coated SS 316L stents showed significant latency (t-test, p < 0.05) with respect to SS 316L and control groups in each test. © 2010 IOP Publishing Ltd.Item Open Access Tuning the degree of oxidation and electron delocalization of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) with solid-electrolyte(Elsevier, 2017-10) Vempati, Sesha; Ertaş, Yelda; Çelebioğlu, Aslı; Uyar, TamerWe report on the effects of ionic interaction on the electronic structure of PEDOT:PSS where the oxidation state of PEDOT is an import aspect for various applications. Additional ionic interactions are introduced and controlled by varying the fraction of poly(ethylene oxide) (PEO). These interactions are balanced against the inherent cohesive forces within each of the polymers constituting intertwined networks. Raman spectra evidenced a peak-shift as high as ∼14 cm−1 for C[dbnd]C vibrational region which suggested increasing degree of oxidation of PEDOT for higher PEO fractions. Changes to the single and bipolaronic absorption bands support the results from the Raman spectra. For highest PEO fraction neutral-PEDOT and lowered bipolaron density is attributed to localization of PEDOT chains within PEO matrix. Interestingly, for higher PEO fractions the electronic density of states (DOS) of HOMO and core-levels (S2p, C1s and O1s) suggested increased degree of oxidation and electron localization on PEDOT. Near and below (∼12 eV) Fermi level, contribution to the O2p and C2p atomic orbitals depicted significantly different DOS. Also we note energetic shift for O2s/C2s and bonding σCC atomic and molecular DOS, respectively. The correlation between some surface and bulk-related properties suggests the uniformity of the blend material which might be vital for the application in electrochemical devices.