Browsing by Subject "Diodes"

Now showing 1 - 12 of 12

Open Access
Capacitance-conductance-current-voltage characteristics of atomic layer deposited Au/Ti/Al2O3/n-GaAs MIS structures
(Elsevier Ltd, 2015) Turut, A.; Karabulut, A.; Ejderha, K.; Bıyıklı, Necmi
We have studied the admittance and current–voltage characteristics of the Au/Ti/Al2O3/nGaAs structure. The Al2O3 layer of about 5 nm was formed on the n-GaAs by atomic layer deposition. The barrier height (BH) and ideality factor values of 1.18 eV and 2.45 were obtained from the forward-bias ln I vs V plot at 300 K. The BH value of 1.18 eV is larger than the values reported for conventional Ti/n-GaAs or Au/Ti/n-GaAs diodes. The barrier modification is very important in metal semiconductor devices. The use of an increased barrier diode as the gate can provide an adequate barrier height for FET operation while the decreased barrier diodes also show promise as small signal zero-bias rectifiers and microwave. The experimental capacitance and conductance characteristics were corrected by taking into account the device series resistance Rs. It has been seen that the noncorrection characteristics cause a serious error in the extraction of the interfacial properties. Furthermore, the device behaved more capacitive at the reverse bias voltage range rather than the forward bias voltage range because the phase angle in the reverse bias has remained unchanged as 901 independent of the measurement frequency.
Open Access
Critical role of CdSe nanoplatelets in color-converting CdSe/ZnS nanocrystals for InGaN/GaN light-emitting diodes
(OSA - The Optical Society, 2016) Hasanov N.; Sharma, V. K.; Martinez, P. L. H.; Tan S.T.; Demir, Hilmi Volkan
Here we report CdSe nanoplatelets that are incorporated into color-converting CdSe/ZnS nanocrystals for InGaN/GaN light-emitting diodes. The critical role of CdSe nanoplatelets as an exciton donor for the color conversion was experimentally investigated. The power conversion efficiency of the hybrid light-emitting diode was found to increase by 23% with the incorporation of the CdSe nanoplatelets. The performance enhancement is ascribed to efficient exciton transfer from the donor CdSe nanoplatelet quantum wells to the acceptor CdSe/ZnS nanocrystal quantum dots through Fï¿½rster-type nonradiative resonance energy transfer.
Open Access
Diode behavior in ultra-thin low temperature ALD grown zinc-oxide on silicon
(AIP Publishing, 2013) El-Atab, N.; Alqatari, S.; Oruc F.B.; Souier, T.; Chiesa, M.; Okyay, Ali Kemal; Nayfeh, A.
A thin-film ZnO(n)/Si(p+) heterojunction diode is demonstrated. The thin film ZnO layer is deposited by Atomic Layer Deposition (ALD) at different temperatures on a p-type silicon substrate. Atomic force microscopy (AFM) AC-in-Air method in addition to conductive AFM (CAFM) were used for the characterization of ZnO layer and to measure the current-voltage characteristics. Forward and reverse bias n-p diode behavior with good rectification properties is achieved. The diode with ZnO grown at 80°C exhibited the highest on/off ratio with a turn-on voltage (VON) ∼3.5 V. The measured breakdown voltage (VBR) and electric field (EBR) for this diode are 5.4 V and 3.86 MV/cm, respectively. © 2013 © 2013 Author(s).
Open Access
Efficiency and harmonic enhancement trends in GaN-based Gunn diodes: Ensemble Monte Carlo analysis
(American Institute of Physics, 2004) Sevik, C.; Bulutay, C.
Gallium nitride can offer a high-power alternative for millimeter-wave Gunn oscillators. Hence, an ensemble Monte Carlo-based comprehensive theoretical assessment of efficiency and harmonic enhancement in n-type GaN Gunn diodes is undertaken. First, the effects of doping notch/mesa and its position within the active channel are investigated which favors a doping notch positioned next to cathode. It is then observed that the width of the notch can be optimized to enhance the higher-harmonic operation without degrading its performance at the fundamental mode. Next, the effects of dc bias and channel doping density are investigated. Both of these have more significant effects on the higher-harmonic efficiency than the fundamental one. The lattice temperature is observed to have almost no influence up to room temperature but severely degrades the performance above room temperature. As a general behavior, the variations of temperature, channel doping, and the notch width primarily affect the phase angle between the current and voltage wave forms rather than the amplitude of oscillations. Finally, the physical origin of these Gunn oscillations is sought which clearly indicates that the intervalley scattering mechanism is responsible rather than the Γ valley nonparabolicity or the effective mass discrepancy between the Γ and the lowest satellite valleys.
Open Access
Electroluminescence efficiency enhancement in quantum dot light-emitting diodes by embedding a silver nanoisland layer
(Wiley-VCH Verlag, 2015) Yang, X.; Hernandez-Martinez, P. L.; Dang C.; Mutlugün, E.; Zhang, K.; Demir, Hilmi Volkan; Sun X. W.
A colloidal quantum dot light-emitting diode (QLED) is reported with substantially enhanced electroluminescence by embedding a thin layer of Ag nanoislands into hole transport layer. The maximum external quantum efficiency (EQE) of 7.1% achieved in the present work is the highest efficiency value reported for green-emitting QLEDs with a similar structure, which corresponds to 46% enhancement compared with the reference device. The relevant mechanisms enabling the EQE enhancement are associated with the near-field enhancement via an effective coupling between excitons of the quantum dot emitters and localized surface plasmons around Ag nano-islands, which are found to lead to good agreement between the simulation results and the experimental data, providing us with a useful insight important for plasmonic QLEDs. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
Open Access
Highly flexible, full-color, top-emitting quantum dot light-emitting diode tapes
(IEEE, 2013) Yang X.; Mutlugün, Evren; Gao, Y.; Zhao, Y.; Tan, S.T.; Sun X.W.; Demir, Hilmi Volkan
We report flexible tapes of high-performance, top-emitting, quantum dot based, light-emitting diodes (QLEDs) with multicolor emission, actively working even when flexed. The resulting QLED tapes reach a high peak luminance level of 19,265 cd/m2. © 2013 IEEE.
Open Access
Implementation of high-quality warm-white light-emitting diodes by a model-experimental feedback approach using quantum dot-salt mixed crystals
(American Chemical Society, 2015) Adam, M.; Erdem, T.; Stachowski, G.M.; Soran-Erdem Z.; Lox, J. F. L.; Bauer, C.; Poppe, J.; Demir, Hilmi Volkan; Gaponik N.; Eychmüller A.
In this work, a model-experimental feedback approach is developed and applied to fabricate high-quality, warm-white light-emitting diodes based on quantum dots (QDs) as color-conversion materials. Owing to their unique chemical and physical properties, QDs offer huge potential for lighting applications. Nevertheless, both emission stability and processability of the QDs are limited upon usage from solution. Incorporating them into a solid ionic matrix overcomes both of these drawbacks, while preserving the initial optical properties. Here borax (Na2B4O7·10H2O) is used as a host matrix because of its lower solubility and thereby reduced ionic strength in water in comparison with NaCl. This guarantees the stability of high-quality CdSe/ZnS QDs in the aqueous phase during crystallization and results in a 3.4 times higher loading amount of QDs within the borax crystals compared to NaCl. All steps from the synthesis via mixed crystal preparation to the warm-white LED preparation are verified by applying the model-experimental feedback, in which experimental data and numerical results provide feedback to each other recursively. These measures are taken to ensure a high luminous efficacy of optical radiation (LER) and a high color rendering index (CRI) of the final device as well as a correlated color temperature (CCT) comparable to an incandescent bulb. By doing so, a warm-white LED with a LER of 341 lm/Wopt, a CCT of 2720 K and a CRI of 91.1 is produced. Finally, we show that the emission stability of the QDs within the borax crystals on LEDs driven at high currents is significantly improved. These findings indicate that the proposed warm-white light-emitting diodes based on QDs-in-borax hold great promise for quality lighting. © 2015 American Chemical Society.
Open Access
Nanocrystal integrated light emitting diodes based on radiative and nonradiative energy transfer for the green gap
(IEEE, 2009) Nizamoğlu, Sedat; Sarı, Emre; Baek J.-H.; Lee I.-H.; Demir, Hilmi Volkan
Recently the photometric conditions for ultra-efficient solid-state lighting have been discussed [1-2]. These studies show that a luminous efficacy of optical radiation at 408 lm/Wopt and a color rendering index (CRI) of 90 at a correlated color temperature (CCT) of 3000 K are achievable at the same time. For this purpose light emitting diodes (LEDs) emitting in blue, green, yellow, and red colors at 463, 530, 573, and 614 nm with relative optical power levels of 1/8, 2/8, 2/8, and 3/8, are required, respectively [1-2]. Although InxGa1-xN material system is capable to cover the whole visible by changing the In composition (x), it is technically extremely challenging to obtain efficient green/yellow light emitting diodes especially at those wavelengths (i.e., at 530 nm and 573 nm, respectively) due to reduced internal quantum efficiency [2-4]. Furthermore, by using the (Al xGa1-x)1-yInyP quaternary alloy it is also possible to cover from 650 nm to 580 nm. However, the efficiencies significantly decrease towards green. Therefore, there exists a significant gap in the green-yellow spectral regions (known as "the green gap") to make efficient light emitting diodes. To address this green gap problem, we propose and demonstrate proof-of-concept nanocrystal (NCs) hybridized green/yellow light emitting diodes that rely on both radiative energy transfer and nonradiative energy transfer (i.e., FRET-Förster resonance energy transfer) for color conversion on near-ultraviolet (near-UV) LEDs.
Open Access
On-chip characterization of THz Schottky diodes using non-contact probes
(IEEE Computer Society, 2016) Khan, T. M.; Ghobadi, A.; Celik, O.; Caglayan, C.; Bıyıklı, Necmi; Okyay, Ali Kemal; Topalli, K.; Sertel, K.
We present non-contact characterization of GaAs Schottky contacts in the 140-220 GHz band. The non-contact probing technique utilizes planar on-chip antennas that are monolithically integrated with the coplanar waveguide environment housing the Schottky diode under test. The diode contact is fabricated through a 6 mask lithographic process with a 5 μm deep-trench under the contact to minimize parasitics and extend operation into the THz band. A quasi-optical link between the VNA ports and on-chip probe antennas enables efficient signal coupling into the test device. The non-contact probe station is calibrated using on-chip quick-offset-short method and the effectiveness of this approach is demonstrated for integrated diodes for under various bias conditions.
Open Access
A performance-enhanced planar Schottky diode for Terahertz applications: an electromagnetic modeling approach
(Cambridge University Press, 2017) Ghobadi, Amir; Khan, Talha Masood; Celik, Ozan Onur; Biyikli, Necmi; Okyay, Ali Kemal; Topalli, Kagan
In this paper, we present the electromagnetic modeling of a performance-enhanced planar Schottky diode for applications in terahertz (THz) frequencies. We provide a systematic simulation approach for analyzing our Schottky diode based on finite element method and lumped equivalent circuit parameter extraction. Afterward, we use the developed model to investigate the effect of design parameters of the Schottky diode on parasitic capacitive and resistive elements. Based on this model, device design has been improved by deep-trench formation in the substrate and using a closed-loop junction to reduce the amount of parasitic capacitance and spreading resistance, respectively. The results indicate that cut-off frequency can be improved from 4.1 to 14.1 THz. Finally, a scaled version of the diode is designed, fabricated, and well characterized to verify the validity of this modeling approach.
Open Access
Skin-like self-assembled monolayers on InAs / GaSb superlattice photodetectors
(IOP Institute of Physics Publishing, 2012) Salihoglu, O.; Muti, A.; Kutluer, K.; Tansel, T.; Turan, R.; Aydınlı, Atilla
We report on the effects of monolayer (ML) thick skin-like octadecanethiol (ODT, CH 3[CH 2] 17SH) on type-II InAs/GaSb MWIR photodetectors. Circumventing the ageing effects of conventional sulfur compounds, we use ODT, a self-assembling, long molecular chain headed with a sulfur atom. Photodiodes coated with and without the self-assembled monolayer (SAM) ODT were compared for their electrical and optical performances. For ODT-coated diodes, the dark current density was improved by two orders of magnitude at 77K under 100mV bias. The zero bias responsivity and detectivity were 1.04AW 1 and 2.15 × 10 13 Jones, respectively, at 4μm and 77K. The quantum efficiency was determined to be 37% for a cutoff wavelength of 5.1μm.
Open Access
Structural and electrical characterizations of InxGa1-xAs/InP structures for infrared photodetector applications
(AIP Publishing LLC, 2014-03-12) Asar, T.; Özçelik, S.; Özbay, Ekmel
Three InGaAs/InP structures for photodetector applications were grown with different indium compositions by MBE technique. The structural properties of the samples have been obtained by means of high resolution X-ray diffraction and secondary ion mass spectrometry measurements. Three InGaAs/InP metal-semiconductor-metal devices were fabricated at room temperature. The experimental forward and reverse bias current-voltage characteristics of the devices such as ideality factor, barrier height, and saturation current were evaluated considering the structural properties of the grown structures. The carrier recombination lifetime and diffusion length in the devices were also calculated using carrier density and mobility data obtained with Hall effect measurement at room temperature. It was determined that all room temperature fabricated devices improved the Schottky barrier height. Especially, the device fabricated on the lower mismatched structure exhibited barrier height enhancement from 0.2 eV, which is the conventional barrier height to 0.642 eV. In addition, the obtained results show that the room temperature fabricated devices on InGaAs/InP structures can be convenient for infrared photodetector applications. (C) 2014 AIP Publishing LLC.