Browsing by Subject "Ultra-fast"
Now showing 1 - 7 of 7
Results Per Page
Sort Options
Item Open Access Femtosecond laser crystallization of amorphous Ge(American Institute of Physics, 2011) Salihoglu, O.; Kürüm, U.; Yaglıoglu, G. H.; Elmali, A.; Aydınlı, AtillaUltrafast crystallization of amorphous germanium (a-Ge) in ambient has been studied. Plasma enhanced chemical vapor deposition grown a-Ge was irradiated with single femtosecond laser pulses of various durations with a range of fluences from below melting to above ablation threshold. Extensive use of Raman scattering has been employed to determine post solidification features aided by scanning electron microscopy and atomic force microscopy measurements. Linewidth of the Ge optic phonon at 300 cm -1 as a function of laser fluence provides a signature for the crystallization of a-Ge. Various crystallization regimes including nanostructures in the form of nanospheres have been identified.Item Open Access Fiber laser-microscope system for femtosecond photodisruption of biological samples(Optical Society of America, 2012-02-22) Yavaş, Seydi; Erdoğan, Mutlu; Gürel, Kutan; İlday, F. Ömer; Eldeniz, Y. B.; Tazebay, Uygar H.We report on the development of a ultrafast fiber lasermicroscope system for femtosecond photodisruption of biological targets. A mode-locked Yb-fiber laser oscillator generates few-nJ pulses at 32.7 MHz repetition rate, amplified up to ~125 nJ at 1030 nm. Following dechirping in a grating compressor, ~240 fs-long pulses are delivered to the sample through a diffraction-limited microscope, which allows real-time imaging and control. The laser can generate arbitrary pulse patterns, formed by two acousto-optic modulators (AOM) controlled by a custom-developed fieldprogrammable gate array (FPGA) controller. This capability opens the route to fine optimization of the ablation processes and management of thermal effects. Sample position, exposure time and imaging are all computerized. The capability of the system to perform femtosecond photodisruption is demonstrated through experiments on tissue and individual cells.Item Open Access High-speed, thermal damage-free ablation of brain tissue with femtosecond pulse bursts(IEEE, 2016) Kerse, Can; Yavaş, Seydi; Kalaycıoğlu, Hamit; Asik M.D.; Akçaalan, Önder; İlday, F. ÖmerWe report a novel ultrafast burst mode fiber laser system and results on ablation of rat brain tissue at rates approaching an order of magnitude improvement over previous reports, with no discernible thermal damage. © 2015 IEEE.Item Open Access Microfluidic measurement of erythrocyte sedimentation rate and monitoring of erytrocyte aggregation(Chemical and Biological Microsystems Society, 2016) Isiksacan, Ziya; Elbuken, ÇağlarWe developed a novel microfluidic opto-electro-mechanical system and performed ultrafast, cheap, and low-sample volume measurement of erythrocyte sedimentation rate (ESR) from erythrocyte aggregation (EA). We also showed EA dynamics in real-time during measurements.Item Open Access Properties of a microjoule-class fiber oscillator mode-locked with a SESAM(IEEE, 2011) Lecaplain, C.; Ortac, Bülend; MacHinet G.; Boullet J.; Baumgartl, M.; Schreiber, T.; Cormier, E.; Hideur, A.Energy scaling of ultrafast Yb-doped fiber oscillators has experienced rapid progress largely driven by many applications that require high average power femtosecond pulses. The fundamental challenge for ultrafast fiber lasers relies on the control of excessive nonlinearity, which limits pulse energy. The development of all-normal dispersion laser cavities based on large-mode-area photonic crystal fibers (PCFs) has enabled significant energy scaling [1-3]. In particular, up to microjoule energy levels have been achieved from rod-type fiber-based oscillators [2-3]. In such lasers, pulse shaping is dominated by the strength of the mode-locking mechanism which determines the pulse properties. In this contribution, we report the generation of high-energy sub-picosecond pulses from a highly normal dispersion fiber laser featuring an Yb-doped rod-type PCF and a large-mode-area PCF [Fig.1(a)]. Passive mode-locking is achieved using saturable absorber mirrors (SAMs). We study the influence of the SAM parameters on performances obtained in this new class of fiber oscillators. The structures exhibit 20 % modulation depths and 500 fs relaxation time with resonant and antiresonant designs. The antiresonant SAM structures ensure absorption bandwidths 45 nm while the resonant structures exhibit 20 nm bandwidths. Stable mode locking with average powers as high as 15 μW at 15 MHz repetition rate, corresponding to microjoule energy level are obtained with all the structures. However, pulse properties and pulse shaping mechanism distinguish between resonant and antiresonant designs. Using a broadband antiresonant SAM leads to generation of highly-chirped pulses with 30 ps duration and 10 nm spectral width [Fig.1(b)]. The output pulses are extra-cavity dechirped down to 550 fs duration. By increasing the strength of the mode-locking mechanism through the combination of the SAM with the NPE process, we obtain shorter pulses with slightly boarder spectra. Indeed, the output pulse duration is decreased from 30 ps to 13 ps by adjusting the wave-plates settings. The dechirped pulse duration is then shortened to 450 fs. We note that the current laser performances are limited to 1 J by the available pump power. Using a resonant SAM structure, the output pulse duration is decreased to 7 ps [Fig.1(b)]. This pulse shortening results from the spectral filtering induced by the limited SAM bandwidth. All these results are in good agreement with numerical simulations which will be discussed in this communication. © 2011 IEEE.Item Open Access Repetition rate tuning of an ultrafast ytterbium doped fiber laser for terahertz time-domain spectroscopy(IEEE, 2013) Keskin H.; Altan H.; Yavaş, Seydi; İlday, F. Ömer; Yagci, M.E.; Aydin O.; Eken, K.; Sahin, B.Repetition rate tuning enables the fast acquisition of THz pulse profiles [1]. By using this method we demonstrate a compact and broadband terahertz time domain spectroscopy system (THz TDS) driven by ytterbium doped fiber laser source. The importance of this method is realized in that Yb:doped fiber lasers can be amplified to sub-millijoule pulse strengths more easily than other types of fiber lasers [2]. Hence, it has the potential to be used in excite-THz probe experiments. Furthermore, the repetition rate-tuning adds flexibility in the excite-probe techniques. These attributes as well as THz generation and detection are investigated with the laser that was developed. © 2013 IEEE.Item Open Access Ultrafast micromachining of Cu and Si at ultra-high repetition rates with pulse bursts(IEEE, 2016) Kerse, Can; Kalaycıoğlu, Hamit; Elahi, Parviz; Yavuz, Koray; Mirza I.; Bulgakova N.M.; İlday, F. ÖmerWe report a novel ultrafast burst mode fiber laser system, which can deliver pulses at ultra-high repetition rates in order to systematically investigate micromachining efficiency on copper and silicon samples. © 2015 IEEE.