Browsing by Author "Akgun, C. O."

Now showing 1 - 6 of 6

Open Access
Effect of post-deposition annealing on the electrical properties of B-Ga2O3 thin films grown on p-Si by plasma-enhanced atomic layer deposition
(American Vacuum Society, 2014-08) Altuntas, H.; Donmez, I.; Akgun, C. O.; Bıyıklı, Necmi
Ga2O3 dielectric thin films were deposited on (111)-oriented p-type silicon wafers by plasma-enhanced atomic layer deposition using trimethylgallium and oxygen plasma. Structural analysis of the Ga 2O3 thin films was carried out using grazing-incidence x-ray diffraction. As-deposited films were amorphous. Upon postdeposition annealing at 700, 800, and 900°C for 30min under N2 ambient, films crystallized into β-form monoclinic structure. Electrical properties of the β-Ga2O3 thin films were then investigated by fabricating and characterizing Al/β-Ga2O3/p-Si metal-oxide-semiconductor capacitors. The effect of postdeposition annealing on the leakage current densities, leakage current conduction mechanisms, dielectric constants, flat-band voltages, reverse breakdown voltages, threshold voltages, and effective oxide charges of the capacitors were presented. The effective oxide charges (Qeff) were calculated from the capacitance-voltage (C-V) curves using the flat-band voltage shift and were found as 2.6×1012, 1.9×1012, and 2.5×10 12 cm-2 for samples annealed at 700, 800, and 900°C, respectively. Effective dielectric constants of the films decreased with increasing annealing temperature. This situation was attributed to the formation of an interfacial SiO2 layer during annealing process. Leakage mechanisms in the regions where current increases gradually with voltage were well fitted by the Schottky emission model for films annealed at 700 and 900°C, and by the Frenkel-Poole emission model for film annealed at 800°C. Leakage current density was found to improve with annealing temperature. β-Ga2O3 thin film annealed at 800°C exhibited the highest reverse breakdown field value. © 2014 American Vacuum Society.
Open Access
Fabrication of hafnia hollow nanofibers by atomic layer deposition using electrospun nanofiber templates
(Elsevier, 2013) Donmez, I.; Kayaci, F.; Akgun, C. O.; Uyar, Tamer; Bıyıklı, Necmi
Hafnia (HfO2) hollow nanofibers (HNs) were synthesized by atomic layer deposition (ALD) using electrospun nylon 6,6 nanofibers as templates. HfO2 layers were deposited on polymeric nanofibers at 200 °C by alternating reactant exposures of tetrakis(dimethylamido)hafnium and water. Polymeric nanofiber templates were subsequently removed by an ex situ calcination process at 500 °C under air ambient. Morphological and structural characterizations of the HN samples were conducted by scanning electron microscopy, transmission electron microscopy and X-ray diffraction. Freestanding network of HfO2 HNs was found to be polycrystalline with a monoclinic crystal structure. Elemental composition and chemical bonding states of the resulting HfO2 HNs were studied by using X-ray photoelectron spectroscopy. The presence of HfO2 was evidenced by high resolution scans of Hf 4f and O 1s with binding energies of 16.3-17.9 and 529.6 eV, respectively. Combination of electrospinning and ALD processes provided an opportunity to precisely control both diameter and wall thickness of the synthesized HfO2 HNs. © 2013 Elsevier B.V. All rights reserved.
Open Access
Low temperature deposition of Ga2O3 thin films using trimethylgallium and oxygen plasma
(A I P Publishing, 2013) Donmez, I.; Akgun, C. O.; Bıyıklı, Necmi
Gallium oxide (Ga2O3) thin films were deposited by plasma-enhanced atomic layer deposition (ALD) using trimethylgallium as the gallium precursor and oxygen plasma as the oxidant. A wide ALD temperature window was observed from 100 to 400 °C, where deposition rate was constant at ∼0.53 Å/cycle. X-ray photoelectron spectroscopy survey scans indicated the presence of gallium, oxygen, and carbon elements with concentrations of ∼36, ∼51.8, and ∼12.2 at. %, respectively. As-deposited films were amorphous; upon annealing at 900 °C under N 2 atmosphere for 30 min, polycrystalline β-Ga2O 3 phase with a monoclinic crystal structure was obtained. Refractive index and root mean square roughness of the annealed Ga2O3 film were higher than those of the as-deposited due to crystallization. © 2013 American Vacuum Society.
Open Access
Polymer-inorganic core-shell nanofibers by electrospinning and atomic layer deposition: Flexible nylon-ZnO core-shell nanofiber mats and their photocatalytic activity
(American Chemical Society, 2012) Kayaci, F.; Akgun, C. O.; Donmez, I.; Bıyıklı, Necmi; Uyar, Tamer
Polymer-inorganic core-shell nanofibers were produced by two-step approach; electrospinning and atomic layer deposition (ALD). First, nylon 6,6 (polymeric core) nanofibers were obtained by electrospinning, and then zinc oxide (ZnO) (inorganic shell) with precise thickness control was deposited onto electrospun nylon 6,6 nanofibers using ALD technique. The bead-free and uniform nylon 6,6 nanofibers having different average fiber diameters (∼80, ∼240 and ∼650 nm) were achieved by using two different solvent systems and polymer concentrations. ZnO layer about 90 nm, having uniform thickness around the fiber structure, was successfully deposited onto the nylon 6,6 nanofibers. Because of the low deposition temperature utilized (200 °C), ALD process did not deform the polymeric fiber structure, and highly conformal ZnO layer with precise thickness and composition over a large scale were accomplished regardless of the differences in fiber diameters. ZnO shell layer was found to have a polycrystalline nature with hexagonal wurtzite structure. The core-shell nylon 6,6-ZnO nanofiber mats were flexible because of the polymeric core component. Photocatalytic activity of the core-shell nylon 6,6-ZnO nanofiber mats were tested by following the photocatalytic decomposition of rhodamine-B dye. The nylon 6,6-ZnO nanofiber mat, having thinner fiber diameter, has shown better photocatalytic efficiency due to higher surface area of this sample. These nylon 6,6-ZnO nanofiber mats have also shown structural stability and kept their photocatalytic activity for the second cycle test. Our findings suggest that core-shell nylon 6,6-ZnO nanofiber mat can be a very good candidate as a filter material for water purification and organic waste treatment because of their photocatalytic properties along with structural flexibility and stability. © 2012 American Chemical Society.
Open Access
Surface-decorated ZnO nanoparticles and ZnO nanocoating on electrospun polymeric nanofibers by atomic layer deposition for flexible photocatalytic nanofibrous membranes
(Royal Society of Chemistry, 2013) Kayaci, F.; Akgun, C. O.; Bıyıklı, Necmi; Uyar, Tamer
Electrospun polymeric nanofibers were either surface-decorated with zinc oxide (ZnO) nanoparticles or coated with a continuous ZnO thin film with a precise thickness (∼27 nm) via atomic layer deposition (ALD) for the fabrication of flexible photocatalytic nanofibrous membranes. © 2013 The Royal Society of Chemistry.
Open Access
Template-based synthesis of aluminum nitride hollow nanofibers via plasma-enhanced atomic layer deposition
(Wiley, 2013) Akgun, C. O.; Kayaci, F.; Donmez, I.; Uyar, Tamer; Bıyıklı, Necmi
Aluminum nitride (AlN) hollow nanofibers were synthesized via plasma-enhanced atomic layer deposition using sacrificial electrospun polymeric nanofiber templates having different average fiber diameters (~70, ~330, and ~740 nm). Depositions were carried out at 200°C using trimethylaluminum and ammonia precursors. AlN-coated nanofibers were calcined subsequently at 500°C for 2 h to remove the sacrificial polymeric nanofiber template. SEM studies have shown that there is a critical wall thickness value depending on the template's average fiber diameter for AlN hollow nanofibers to preserve their shapes after the template has been removed by calcination. Best morphologies were observed for AlN hollow nanofibers prepared by depositing 800 cycles (corresponding to ~69 nm) on nanofiber templates having ~330 nm average fiber diameter. TEM images indicated uniform wall thicknesses of ~65 nm along the fiber axes for samples prepared using templates having ~70 and ~330 nm average fiber diameters. Synthesized AlN hollow nanofibers were polycrystalline with a hexagonal crystal structure as determined by high-resolution TEM and selected area electron diffraction. Chemical compositions of coated and calcined samples were studied using X-ray photoelectron spectroscopy (XPS). High-resolution XPS spectra confirmed the presence of AlN. © 2012 The American Ceramic Society.