Browsing by Subject "Strain sensors"

Now showing 1 - 6 of 6

Open Access
An electromagnetic sensing system incorporating multiple probes and single antenna for wireless structural health monitoring
(IEEE, 2017) Özbey, Burak; Altıntaş, Ayhan; Demir, Hilmi Volkan; Ertürk, Vakur B.; Kurç, Ö.
In this study, a wireless and passive displacement/strain sensing system is proposed for structural health monitoring (SHM). The wireless and passive interrogation of the sensing unit [a variant of a nested split-ring resonator (NSRR)] is achieved through the near-field interaction and electromagnetic coupling between the single antenna in the system and the multiple sensors called the NSRR probes. It is demonstrated that the system can acquire data from more than one NSRR probe simultaneously in a real-life scenario, where the probes are confined within concrete inside a beam, while the antenna monitors them from outside.
Open Access
Flexible metamaterials for wireless strain sensing
(American Institute of Physics, 2009-11-04) Melik, R.; Unal, E.; Perkgoz, N. K.; Puttlitz, C.; Demir, Hilmi Volkan
We proposed and demonstrated flexible metamaterial-based wireless strain sensors that include arrays of split ring resonators (SRRs) to telemetrically measure strain. For these metamaterial sensors, we showed that a flexible substrate (e.g., Kapton tape) delivers greater sensitivity and a more linear response as compared to using silicon substrates. Specifically, these tape-based flexible SRR sensors exhibit a significantly improved sensitivity level of 0.292 MHz/kgf with a substantially reduced nonlinearity error of 3% for externally applied mechanical loads up to 250 kgf. These data represent a sixfold increase in sensitivity and a 16-fold reduction in error percentage.
Open Access
Metamaterial-based wireless strain sensors
(American Institute of Physics, 2009-07-07) Melik, R.; Unal, E.; Perkgoz, N. K.; Puttlitz, C.; Demir, Hilmi Volkan
We proposed and demonstrated metamaterial-based strain sensors that are highly sensitive to mechanical deformation. Their resonance frequency shift is correlated with the surface strain of our test material and the strain data are reported telemetrically. These metamaterial sensors are better than traditional radio-frequency (rf) structures in sensing for providing resonances with high quality factors and large transmission dips. Using split ring resonators (SRRs), we achieve lower resonance frequencies per unit area compared to other rf structures, allowing for bioimplant sensing in soft tissue (e.g., fracture healing). In 5×5 SRR architecture, our wireless sensors yield high sensitivity (109 kHz/kgf, or 5.148 kHz/microstrain) with low nonlinearity error (<200 microstrain).
Open Access
Nested metamaterials for wireless strain sensing
(IEEE, 2009-12-28) Melik, R.; Unal, E.; Perkgoz, N. K.; Santoni, B.; Kamstock, D.; Puttlitz, C.; Demir, Hilmi Volkan
We designed, fabricated, and characterized metamaterial-based RF-microelectromechanical system (RF-MEMS) strain sensors that incorporate multiple split ring resonators (SRRs) in a compact nested architecture to measure strain telemetrically. We also showed biocompatibility of these strain sensors in an animal model. With these devices, our bioimplantable wireless metamaterial sensors are intended, to enable clinicians, to quantitatively evaluate the progression of long-bone fracture healing by monitoring the strain on the implantable fracture fixation hardware in real time. In operation, the transmission spectrum of the metamaterial sensor attached to the implantable fixture is changed when an external load is applied to the fixture, and from this change, the strain is recorded remotely. By employing telemetric characterizations, we reduced the operating frequency and enhanced the sensitivity of our novel nested SRR architecture compared to the conventional SRR structure. The nested SRR structure exhibited a higher sensitivity of 1.09 kHz/kgf operating at lower frequency compared to the classical SRR that demonstrated a sensitivity of 0.72 kHz/kgf. Using soft tissue medium, we achieved the best sensitivity level of 4.00 kHz/kgf with our nested SRR sensor. Ultimately, the laboratory characterization and in vivo biocompatibility studies support further development and characterization of a fracture healing system based on implantable nested SRR.
Open Access
Wavelength tuning of the spirally drawn whispering gallery mode microfiber lasers and the perspectives for sensing applications
(OSA - The Optical Society, 2017) Yang, Shancheng; Eugene, Tay Yong Kang; Wang, Yue; Zhao, Xin; Demir, Hilmi Volkan; Sun, Handong
Facile and cost-efficient microcavities, as well as the tuning of the optical modes, especially for the application of top-grade optical devices, have been emerging as attractive research fields. In this work, controllable fabrication of the microfiber laser arrays in polymer matrix is achieved by employing the advanced spiral drawing technique. Besides the high-quality whispering gallery mode (WGM) lasing, wavelength tuning is also realized by applying external forces on the polymer matrix, which induce slightly enlarged cavity sizes. Furthermore, the perspectives of utilizing the microfiber arrays as force and strain sensors are discussed and demonstrated. ï¿½ 2017 Optical Society of America.
Open Access
Wireless sensing in complex electromagnetic media: construction materials and structural monitoring
(Institute of Electrical and Electronics Engineers Inc., 2015) Özbey, B.; Demir, Hilmi Volkan; Kurc, O.; Ertürk, V. B.; Altıntaş, A.
In this paper, wireless sensing in the presence of complex electromagnetic media created by combinations of reinforcing bars and concrete is investigated. The wireless displacement sensing system, primarily designed for use in structural health monitoring (SHM), is composed of a comb-like nested split-ring resonator (NSRR) probe and a transceiver antenna. Although each complex medium scenario is predicted to have a detrimental effect on sensing in principle, it is demonstrated that the proposed sensor geometry is able to operate fairly well in all scenarios except one. In these scenarios that mimic real-life SHM, it is shown that this sensor exhibits a high displacement resolution of 1 μm, a good sensitivity of 7 MHz/mm in average, and a high dynamic range extending over 20 mm. For the most disruptive scenario of placing concrete immediately behind NSRR, a solution based on employing a separator behind the probe is proposed to overcome the handicaps introduced by the medium. In order to obtain a one-to-one mapping from the measured frequency shift to the displacement, a numerical fit is proposed and used. The effects of several complex medium scenarios on this fit are discussed. These results indicate that the proposed sensing scheme works well in real-life SHM applications. © 2001-2012 IEEE.