Browsing by Subject "Frequency shift"

Filter results by typing the first few letters
Now showing 1 - 4 of 4
  • Thumbnail Image
    ItemOpen Access
    Circular high-Q resonating isotropic strain sensors with large shift of resonance frequency under stress
    (2009) Melik, R.; Unal, E.; Perkgoz, N.K.; Puttlitz, C.; Demir, Hilmi Volkan
    We present circular architecture bioimplant strain sensors that facilitate a strong resonance frequency shift with mechanical deformation. The clinical application area of these sensors is for in vivo assessment of bone fractures. Using a rectangular geometry, we obtain a resonance shift of 330 MHz for a single device and 170 MHz for its triplet configuration (with three side-by-side resonators on chip) under an applied load of 3,920 N. Using the same device parameters with a circular isotropic architecture, we achieve a resonance frequency shift of 500 MHz for the single device and 260 MHz for its triplet configuration, demonstrating substantially increased sensitivity. © 2009 by the authors.
  • Thumbnail Image
    ItemOpen Access
    Dual-frequency division de-multiplexer based on cascaded photonic crystal waveguides
    (Elsevier, 2012-02-28) Akosman, Ahmet E.; Mutlu, Mehmet; Kurt, H.; Özbay, Ekmel
    A dual-frequency division de-multiplexing mechanism is demonstrated using cascaded photonic crystal waveguides with unequal waveguide widths. The de-multiplexing mechanism is based on the frequency shift of the waveguide bands for the unequal widths of the photonic crystal waveguides. The modulation in the waveguide bands is used for providing frequency selectivity to the system. The slow light regime of the waveguide bands is utilized for extracting the desired frequency bands from a wider photonic crystal waveguide that has a relatively larger group velocity than the main waveguide for the de-multiplexed frequencies. In other words, the wider spatial distribution of the electric fields in the transverse direction of the waveguide for slow light modes is utilized in order to achieve the dropping of the modes to the output channels. The spectral and spatial de-multiplexing features are numerically verified. It can be stated that the presented mechanism can be used to de-multiplex more than two frequency intervals by cascading new photonic crystal waveguides with properly selected widths.
  • Thumbnail Image
    ItemOpen Access
    Metamaterial based telemetric strain sensing in different materials
    (Optical Society of American (OSA), 2010) Melik, R.; Unal, E.; Perkgoz, N.K.; Puttlitz, C.; Demir, Hilmi Volkan
    We present telemetric sensing of surface strains on different industrial materials using split-ring-resonator based metamaterials. For wireless strain sensing, we utilize metamaterial array architectures for high sensitivity and low nonlinearity-errors in strain sensing. In this work, telemetric strain measurements in three test materials of cast polyamide, derlin and polyamide are performed by observing operating frequency shift under mechanical deformation and these data are compared with commercially-available wired strain gauges. We demonstrate that hard material (cast polyamide) showed low slope in frequency shift vs. applied load (corresponding to high Young's modulus), while soft material (polyamide) exhibited high slope (low Young's modulus).
  • Thumbnail Image
    ItemOpen Access
    Optimizing CMUT geometry for high power
    (IEEE, 2010) Yamaner F.Y.; Olcum, Selim; Bozkurt, A.; Köymen, Hayrettin; Atalar, Abdullah
    Capacitive micromachined ultrasonic transducers (CMUTs) have demonstratedvarious advantages over piezoelectric transducers. However, current CMUT designsproduce low output pressures with high harmonic distortions. Optimizing thetransducer parameters requires an iterative solution and is too time consumingusing finite element (FEM) modelling tools. In this work, we present a method ofdesigning high output pressure CMUTs with relatively low distortion. We analyzethe behavior of a membrane under high voltage continuous wave operation using anonlinear electrical circuit model. The radiation impedance of an array ofCMUTs is accurately represented using an RLC circuit in the model. The maximummembrane swing without collapse is targeted in the transmit mode. Using SPICEsimulation of the parametric circuit model, we design the CMUT cell withoptimized parameters such as the membrane radius (a), thickness (tm),insulator thickness (ti) and gap height (tg). The modelalso predicts the amount of second harmonic at the output. To verify theaccuracy of the results, we built a FEM model with the same CMUT parameters. Thedesign starts by choosing ti for the given input voltage level.First, a is selected for the maximum radiation resistance of the array at theoperating frequency. Second, tm is found for the resonance at theinput frequency. Third, tg is chosen for the maximum membrane swing.Under this condition, a frequency shift in the resonant frequency occurs. Secondand third steps are repeated until convergence. This method results in a CMUTarray with a high output power and with low distortion. © 2010 IEEE.