Browsing by Subject "Amorphization"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Open Access Extracting the temperature distribution on a phase-change memory cell during crystallization(American Institute of Physics Inc., 2016-10) Bakan, G.; Gerislioglu, B.; Dirisaglik, F.; Jurado, Z.; Sullivan, L.; Dana, A.; Lam, C.; Gokirmak A.; Silva, H.Phase-change memory (PCM) devices are enabled by amorphization- and crystallization-induced changes in the devices' electrical resistances. Amorphization is achieved by melting and quenching the active volume using short duration electrical pulses (∼ns). The crystallization (set) pulse duration, however, is much longer and depends on the cell temperature reached during the pulse. Hence, the temperature-dependent crystallization process of the phase-change materials at the device level has to be well characterized to achieve fast PCM operations. A main challenge is determining the cell temperature during crystallization. Here, we report extraction of the temperature distribution on a lateral PCM cell during a set pulse using measured voltage-current characteristics and thermal modelling. The effect of the thermal properties of materials on the extracted cell temperature is also studied, and a better cell design is proposed for more accurate temperature extraction. The demonstrated study provides promising results for characterization of the temperature-dependent crystallization process within a cell.Item Open Access Formation of B19′, B2, and amorphous phases during mechano-synthesis of nanocrystalline NiTi intermetallics(Elsevier BV, 2014-02) Amini, R.; Alijani, F.; Ghaffari, M.; Alizadeh, M.; Okyay, Ali KemalNi-50Ti shape memory alloy was synthesized by mechanical alloying of the elemental powders mixture under an argon gas atmosphere. The structural and microstructural properties of the alloyed powders were evaluated by X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. Moreover, the Vickers microhardness of the powders was estimated at different milling times. According to the results, by milling progression, the amount of the amorphous phase increased considerably and after sufficient milling time (48h), the mechano-crystallization of the amorphous phase into the more stable crystalline phases (i.e. B2 and B19') occurred. It was found that the particles size and microhardness were significantly affected by the formation of the amorphous, B2, and B19' phases. It was also deduced that, by appropriate heating and cooling cycles, the B2 and thermally-induced B19' phases can be created. Furthermore, it was inferred that the formation of undesirable intermetallic phases (particularly NiTi2) during the heating cycle was considerably reduced by milling time evolution. © 2013 Elsevier B.V.Item Open Access Ultrathin phase-change coatings on metals for electrothermally tunable colors(American Institute of Physics Inc., 2016-08) Bakan, G.; Ayas S.; Saidzoda, T.; Celebi, K.; Dana, A.Metal surfaces coated with ultrathin lossy dielectrics enable color generation through strong interferences in the visible spectrum. Using a phase-change thin film as the coating layer offers tuning the generated color by crystallization or re-amorphization. Here, we study the optical response of surfaces consisting of thin (5-40 nm) phase-changing Ge2Sb2Te5 (GST) films on metal, primarily Al, layers. A color scale ranging from yellow to red to blue that is obtained using different thicknesses of as-deposited amorphous GST layers turns dim gray upon annealing-induced crystallization of the GST. Moreover, when a relatively thick (>100 nm) and lossless dielectric film is introduced between the GST and Al layers, optical cavity modes are observed, offering a rich color gamut at the expense of the angle independent optical response. Finally, a color pixel structure is proposed for ultrahigh resolution (pixel size: 5 × 5 μm2), non-volatile displays, where the metal layer acting like a mirror is used as a heater element. The electrothermal simulations of such a pixel structure suggest that crystallization and re-amorphization of the GST layer using electrical pulses are possible for electrothermal color tuning.