Browsing by Author "Eken, K."

Now showing 1 - 13 of 13

Open Access
50-W, 1.6-GHz pulse repetition rate from a burst-mode Yb-doped fiber laser
(IEEE, 2017) Elahi, Parviz; Ertek, A. C.; Eken, K.; İlday, Fatih Ömer
We report a 50-W average power Yb-doped fiber laser amplifier system. The laser system produces bursts at a minimum rate of 200 kHz, with 1.6 GHz intraburst repetition rate. The total energy delivers in a burst is 250 μJ and the individual pulse energy is about 0.4 μJ. The output pulses are compressed to 270 fs by using two compressor gratings.
Open Access
83 W, 1 ns, 3.1 MHz all-fiber laser for micromachining
(IEEE, 2011) Özgören, Kıvanç; Öktem, Bülent; Yılmaz, Sinem; İlday, F. Ömer; Pasin, E.; Eken, K.
Fiber lasers are commonly used for various material processing applications. The advantages (such as simplicity of the system, high material removal rate) and disadvantages (larger heat-affected zone, reduced precision) of nanosecond pulses over sub-picosecond pulses are well known. © 2011 IEEE.
Open Access
83 W, 3.1 MHz, square-shaped, 1 ns-pulsed all-fiber-integrated laser for micromachining
(Optical Society of America, 2011-08-29) Özgören, Kıvanç; Öktem, Bülent; Yılmaz, Sinem; İlday, F. Ömer; Eken, K.
We demonstrate an all-fiber-integrated laser based on off-the-shelf components producing square-shaped, 1 ns-long pulses at 1.03 mu m wavelength with 3.1 MHz repetition rate and 83 W of average power. The master-oscillator power-amplifier system is seeded by a fiber oscillator utilizing a nonlinear optical loop mirror and producing incompressible pulses. A simple technique is employed to demonstrate that the pulses indeed have a random chirp. We propose that the long pulse duration should result in more efficient material removal relative to picosecond pulses, while being short enough to minimize heat effects, relative to nanosecond pulses commonly used in micromachining. Micromachining of Ti surfaces using 0.1 ns, 1 ns and 100 ns pulses supports these expectations. (C) 2011 Optical Society of America
Open Access
Burst-mode Yb fiber amplifier producing 30 μJ individual pulse energy
(Optical Society of America, 2012) Kalaycıoğlu, Hamit; Burak Eldeniz, Y.; İlday, F. Ömer; Eken, K.
We report 30-μJ individual pulse energy for 150-ns long amplified bursts of 0.4 mJ total energy from a 1-kHz Yb-fiber amplifier. Non-uniformity of pulse energy distribution inside amplified bursts is significantly reduced. ©2012 Optical Society of America.
Open Access
Development of a rapid-scan fiber-integrated terahertz spectrometer
(Springer New York LLC, 2014) Keskin, H.; Altan, H.; Yavas, S.; Ilday, F. O.; Eken, K.; Sahin, A. B.
Scientists in terahertz (THz) wave technologies have benefited from the recent developments in ultrafast laser technologies and RF technologies and applied these new gained techniques into characterizing a wide variety of phenomena. Undoubtedly, the most successful of these applications has been in the development of time-domain terahertz spectroscopic and imaging systems which has been utilized in the characterization of dielectrics and semiconductors. This pulsed technique has allowed users to characterize dynamical behavior inside materials under illumination with picosecond resolution. Typically pump/probe or similar dynamical measurements require the use of amplified pulses derived from free-space solid state lasers in the μJ-mJ range and since interferometric techniques are typically used in pulsed measurements the measurement time of a THz spectrum can last at least tens of minutes. Better systems can be realized based on fiber laser technologies. Here we discuss the advantages of a THz spectrometer driven by an ultrafast Ytterbium doped fiber laser whose repetition rate can be tuned rapidly allowing for rapid dynamical measurements. The efficient gain medium, robust operation and compact design of the system opens up the possibility of exploring rapid detection of various materials as well as studying dynamical behavior using the high brightness source.
Open Access
Doping management for high-power fiber lasers: 100 W, few-picosecond pulse generation from an all-fiber-integrated amplifier
(Optical Society of America, 2012-07-16) Elahi, P.; Yilmaz, S.; Akçaalan, Ö.; Kalaycioğlu, H.; Öktem, B.; Şenel, Ç.; Ilday, F. Ö.; Eken, K.
Thermal effects, which limit the average power, can be minimized by using low-doped, longer gain fibers, whereas the presence of nonlinear effects requires use of high-doped, shorter fibers to maximize the peak power. We propose the use of varying doping levels along the gain fiber to circumvent these opposing requirements. By analogy to dispersion management and nonlinearity management, we refer to this scheme as doping management. As a practical first implementation, we report on the development of a fiber laser-amplifier system, the last stage of which has a hybrid gain fiber composed of high-doped and low-doped Yb fibers. The amplifier generates 100 W at 100 MHz with pulse energy of 1 μJ. The seed source is a passively mode-locked fiber oscillator operating in the all-normaldispersion regime. The amplifier comprises three stages, which are all-fiber-integrated, delivering 13 ps pulses at full power. By optionally placing a grating compressor after the first stage amplifier, chirp of the seed pulses can be controlled, which allows an extra degree of freedom in the interplay between dispersion and self-phase modulation. This way, the laser delivers 4.5 ps pulses with ∼200 kW peak power directly from fiber, without using external pulse compression.
Open Access
Doping management in high power fiber amplifiers: optimization of heat generation and nonlinear phase shift
(2012) Elahi, P.; Yılmaz, S.; Akçaalan, O.; Kalaycıoğlu, H.; Öktem, B.; Şenel, C.; Eken, K.
Open Access
Fiber amplification of pulse bursts up to 20 μj pulse energy at 1 kHz repetition rate
(Optical of Society of America, 2011-08-23) Kalaycıoğlu, Hamit; Eken, K.; İlday, F. Ömer
We demonstrate burst-mode operation of a polarization-maintaining Yb-doped fiber amplifier. Groups of pulses with a temporal spacing of 10 ns and 1 kHz overall repetition rate are amplified to an average pulse energy of ∼20 μJ and total burst energy of 0:25 mJ. The pulses are externally compressed to ∼400 fs. The amplifier is synchronously pulsed-pumped to minimize amplified spontaneous emission between the bursts. We characterize the influence of pump pulse duration, pump-to-signal delay, and signal burst length.
Open Access
High-power Yb-based all-fiber laser delivering 300 fs pulses for high-speed ablation-cooled material removal
(OSA - The Optical Society, 2018) Elahi, P.; Akçaalan, Ö.; Ertek, C.; Eken, K.; İlday, Fatih Ömer; Kalaycoglu, H.
We report on a 72 W Yb all-fiber ultrafast laser system with 1.6 GHz intra-burst and 200 kHz burst repetition rate developed to demonstrate ablation-cooled material removal at high speeds. Up to 24 W is applied on Cu and Si samples with pulses of ~300 fs, and record-high ablation efficiencies are obtained, compared to published results to date, despite using only ~100 nJ pulses. Ablation speeds approaching 1 mm3∕s are reported with 24 W of average power, limited by available laser power and beam scanning speed. More significantly, these results experimentally confirm the theoretically expected linear scaling of the ablation-cooled regime to higher average powers without sacrificing efficiency, which implies that further scaling is possible with further increases in laser power and scanning speeds.
Open Access
Micromachining with square-Shaped 1 ns-Long pulses from an all-Fiber Yb-Doped laser-Amplifier system
(Optical Society of America, 2011) Özgören, Kıvanç; Öktem, Bülent; İlday, F. Ömer; Pasin, Ece; Eken, K.
We demonstrate micromachining with 1ns-long pulses from an all-fiber laser. Fiber lasers generating uncompressible long pulses have been ignored as undesired operational modes, however their robust, low-repetition-rate operation is well suited to micromachining. © 2011 Optical Society of America.
Open Access
Repetition rate tuning of an ultrafast ytterbium doped fiber laser for terahertz time-domain spectroscopy
(IEEE, 2013) Keskin H.; Altan H.; Yavaş, Seydi; İlday, F. Ömer; Yagci, M.E.; Aydin O.; Eken, K.; Sahin, B.
Repetition rate tuning enables the fast acquisition of THz pulse profiles [1]. By using this method we demonstrate a compact and broadband terahertz time domain spectroscopy system (THz TDS) driven by ytterbium doped fiber laser source. The importance of this method is realized in that Yb:doped fiber lasers can be amplified to sub-millijoule pulse strengths more easily than other types of fiber lasers [2]. Hence, it has the potential to be used in excite-THz probe experiments. Furthermore, the repetition rate-tuning adds flexibility in the excite-probe techniques. These attributes as well as THz generation and detection are investigated with the laser that was developed. © 2013 IEEE.
Open Access
Surface texturing of dental implant surfaces with an ultrafast fiber laser
(Optical Society of America, 2010) Öktem, Bülent; Kalaycıoğlu, Hamit; Erdoǧan, M.; Yavaş, S.; Mukhopadhyay P.; Tazebay, Uygar Halis; Aykaç, Y.; Eken, K.; İlday, F. Ömer
Controlled modification of implant surfaces using femtosecond, picosecond and nanosecond pulses from home-built all-fiber-integrated lasers is demonstrated. Picosecond and femtosecond pulses offer superior control over the surface texture. Increasing cell attachment to surface is discussed. ©2010 Optical Society of America.
Open Access
Texturing of titanium (Ti6Al4V) medical implant surfaces with MHz-repetition-rate femtosecond and picosecond Yb-doped fiber lasers
(Optical Society of American (OSA), 2011) Erdoǧan, M.; Öktem, B.; Kalaycioǧlu H.; Yavaş, S.; Mukhopadhyay P.K.; Eken, K.; Özgören, K.; Aykaç, Y.; Tazebay, U.H.; Ilday F.O.
We propose and demonstrate the use of short pulsed fiber lasers in surface texturing using MHz-repetition-rate, microjoule- and sub-microjoule-energy pulses. Texturing of titanium-based (Ti6Al4V) dental implant surfaces is achieved using femtosecond, picosecond and (for comparison) nanosecond pulses with the aim of controlling attachment of human cells onto the surface. Femtosecond and picosecond pulses yield similar results in the creation of micron-scale textures with greatly reduced or no thermal heat effects, whereas nanosecond pulses result in strong thermal effects. Various surface textures are created with excellent uniformity and repeatability on a desired portion of the surface. The effects of the surface texturing on the attachment and proliferation of cells are characterized under cell culture conditions. Our data indicate that picosecond-pulsed laser modification can be utilized effectively in low-cost laser surface engineering of medical implants, where different areas on the surface can be made cell-attachment friendly or hostile through the use of different patterns. © 2011 Optical Society of America.