Browsing by Author "Perkgoz, N. K."
Now showing 1 - 10 of 10
Results Per Page
Sort Options
Item Open Access Bio-implantable passive on-chip RF-MEMS strain sensing resonators for orthopaedic applications(Institute of Physics Publishing Ltd., 2008) Melik, R.; Perkgoz, N. K.; Unal, E.; Puttlitz, C.; Demir, Hilmi VolkanOne out of ten bone fractures does not heal properly due to improper load distribution and strain profiles during the healing process. To provide implantable tools for the assessment of bone fractures, we have designed novel, bio-implantable, passive, on-chip, RF-MEMS strain sensors that rely on the resonance frequency shift with mechanical deformation. For this purpose, we modeled, fabricated and experimentally characterized two on-chip sensors with high quality factors for in vivo implantation. One of the sensors has an area of ∼0.12 mm2 with a quality factor of ∼60 and the other has an area of ∼0.07 mm2 with a quality factor of ∼70. To monitor the mechanical deformation by measuring the change in the resonance frequencies with the applied load, we employed a controllable, point load applying experimental setup designed and constructed for in vitro characterization. In the case of the sensor with the larger area, when we apply a load of 3920 N, we obtain a frequency shift of ∼330 MHz and a quality factor of ∼76. For the smaller sensor, the frequency shift and the quality factor are increased to 360 MHz and 95, respectively. These data demonstrate that our sensor chips have the capacity to withstand relatively high physiologic loads, and that the concomitant and very large resonant frequency shift with the applied load is achieved while maintaining a high signal quality factor. These experiments demonstrate that these novel sensors have the capacity for producing high sensitivity strain readout, even when the total device area is considerably small. Also, we have demonstrated that our bio-implantable, passive sensors deliver a telemetric, real-time readout of the strain on a chip. Placing two more resonators on the sides of the sensor to serve as transmitter and receiver antennas, we achieved to transfer contactless power and read out loads in the absence of direct wiring to the sensor. With this model, where telemetric measurements become simpler due to the fact that all sensor system is built on the same chip, we obtain a frequency shift of ∼190 MHz with an increase in the quality factor from ∼38 to ∼46 when a load of 3920 N is applied. Therefore, as a first proof of concept, we have demonstrated the feasibility of our on-chip strain sensors for monitoring the mechanical deformation using telemetry-based systems.Item Open Access Comparative study of optically activated nanocomposites with photocatalytic TiO2 and ZnO nanoparticles for massive environmental decontamination(S P I E - International Society for Optical Engineering, 2007) Tek, S.; Mutlugun, E.; Soganci, I. M.; Perkgoz, N. K.; Yucel, D.; Celiker, G.; Demir, Hilmi VolkanNanocomposites that incorporate TiO2 and ZnO nanoparticles separately in three-dimensional solgel matrices through full chemical integration are prepared to perform highly efficient photocatalytic activities for applications of environmental decontamination. Spectral responses of photocatalytic TiO2 and ZnO nanoparticles exposed to UV activation for self-cleaning process were obtained as also their optical relative spectral efficiency curves from 270 to 370 nm in the UV regime. Our investigations of the optimal conditions to increase their spectral photocatalytic efficiencies resulted in remarkably high levels of optical recovery and efficiency.Item Open Access Design and realization of a fully on-chip High-Q resonator at 15 GHz on silicon(Institute of Electrical and Electronics Engineers, 2008-12) Melik, R.; Perkgoz, N. K.; Unal, E.; Dilli, Z.; Demir, Hilmi VolkanWe develop and demonstrate an on-chip resonator working at 15 GHz with a high quality factor (Q-factor) of 93.81 while only requiring a small chip size of 195 mu m x 195 mu m on Si by using our new design methodology. In our design, unlike previous approaches, we avoid the need for any external capacitance for tuning; instead, we utilize the film capacitance as the capacitor of the LC tank circuit and realize a fully on-chip resonator that shows a strong transmission dip of > 30 dB on resonance as required for telemetric-sensing applications. We present the design, theory, methodology, microfabrication, experimental characterization, and theoretical analysis of these resonators. We also demonstrate that the experimental results are in excellent agreement with the theoretical (both analytical and numerical) results. Based on our proof-of-concept demonstration, such high-Q on-chip resonators hold great promise for use in transmissive telemetric sensors.Item Open Access Flexible metamaterials for wireless strain sensing(American Institute of Physics, 2009-11-04) Melik, R.; Unal, E.; Perkgoz, N. K.; Puttlitz, C.; Demir, Hilmi VolkanWe proposed and demonstrated flexible metamaterial-based wireless strain sensors that include arrays of split ring resonators (SRRs) to telemetrically measure strain. For these metamaterial sensors, we showed that a flexible substrate (e.g., Kapton tape) delivers greater sensitivity and a more linear response as compared to using silicon substrates. Specifically, these tape-based flexible SRR sensors exhibit a significantly improved sensitivity level of 0.292 MHz/kgf with a substantially reduced nonlinearity error of 3% for externally applied mechanical loads up to 250 kgf. These data represent a sixfold increase in sensitivity and a 16-fold reduction in error percentage.Item Open Access Metamaterial-based wireless strain sensors(American Institute of Physics, 2009-07-07) Melik, R.; Unal, E.; Perkgoz, N. K.; Puttlitz, C.; Demir, Hilmi VolkanWe proposed and demonstrated metamaterial-based strain sensors that are highly sensitive to mechanical deformation. Their resonance frequency shift is correlated with the surface strain of our test material and the strain data are reported telemetrically. These metamaterial sensors are better than traditional radio-frequency (rf) structures in sensing for providing resonances with high quality factors and large transmission dips. Using split ring resonators (SRRs), we achieve lower resonance frequencies per unit area compared to other rf structures, allowing for bioimplant sensing in soft tissue (e.g., fracture healing). In 5×5 SRR architecture, our wireless sensors yield high sensitivity (109 kHz/kgf, or 5.148 kHz/microstrain) with low nonlinearity error (<200 microstrain).Item Open Access Near-unity efficiency energy transfer from colloidal semiconductor quantum wells of CdSe/cdS nanoplatelets to a monolayer of MoS2(American Chemical Society, 2018) Taghipour, N.; Martinez, P. L. H.; Ozden, A.; Olutas M.; Dede, D.; Gungor K.; Erdem, O.; Perkgoz, N. K.; Demir, Hilmi VolkanA hybrid structure of the quasi-2D colloidal semiconductor quantum wells assembled with a single layer of 2D transition metal dichalcogenides offers the possibility of highly strong dipole-to-dipole coupling, which may enable extraordinary levels of efficiency in Förster resonance energy transfer (FRET). Here, we show ultrahigh-efficiency FRET from the ensemble thin films of CdSe/CdS nanoplatelets (NPLs) to a MoS2 monolayer. From time-resolved fluorescence spectroscopy, we observed the suppression of the photoluminescence of the NPLs corresponding to the total rate of energy transfer from ∼0.4 to 268 ns-1. Using an Al2O3 separating layer between CdSe/CdS and MoS2 with thickness tuned from 5 to 1 nm, we found that FRET takes place 7- to 88-fold faster than the Auger recombination in CdSe-based NPLs. Our measurements reveal that the FRET rate scales down with d-2 for the donor of CdSe/CdS NPLs and the acceptor of the MoS2 monolayer, d being the center-to-center distance between this FRET pair. A full electromagnetic model explains the behavior of this d-2 system. This scaling arises from the delocalization of the dipole fields in the ensemble thin film of the NPLs and full distribution of the electric field across the layer of MoS2. This d-2 dependency results in an extraordinarily long Förster radius of ∼33 nm.Item Open Access Nested metamaterials for wireless strain sensing(IEEE, 2009-12-28) Melik, R.; Unal, E.; Perkgoz, N. K.; Santoni, B.; Kamstock, D.; Puttlitz, C.; Demir, Hilmi VolkanWe designed, fabricated, and characterized metamaterial-based RF-microelectromechanical system (RF-MEMS) strain sensors that incorporate multiple split ring resonators (SRRs) in a compact nested architecture to measure strain telemetrically. We also showed biocompatibility of these strain sensors in an animal model. With these devices, our bioimplantable wireless metamaterial sensors are intended, to enable clinicians, to quantitatively evaluate the progression of long-bone fracture healing by monitoring the strain on the implantable fracture fixation hardware in real time. In operation, the transmission spectrum of the metamaterial sensor attached to the implantable fixture is changed when an external load is applied to the fixture, and from this change, the strain is recorded remotely. By employing telemetric characterizations, we reduced the operating frequency and enhanced the sensitivity of our novel nested SRR architecture compared to the conventional SRR structure. The nested SRR structure exhibited a higher sensitivity of 1.09 kHz/kgf operating at lower frequency compared to the classical SRR that demonstrated a sensitivity of 0.72 kHz/kgf. Using soft tissue medium, we achieved the best sensitivity level of 4.00 kHz/kgf with our nested SRR sensor. Ultimately, the laboratory characterization and in vivo biocompatibility studies support further development and characterization of a fracture healing system based on implantable nested SRR.Item Open Access Photocatalytic hybrid nanocomposites of metal oxide nanoparticles enhanced towards the visible spectral range(Elsevier, 2011-04-13) Perkgoz, N. K.; Toru, R. S.; Unal, E.; Sefunc, M.A.; Tek, S.; Mutlugun, E.; Soganci, I. M.; Celiker, H.; Celiker, G.; Demir, Hilmi VolkanWe propose and demonstrate photocatalytic hybrid nanocomposites that co-integrate TiO(2) and ZnO nanoparticles in the same host resin to substantially enhance their combined photocatalytic activity in the near-UV and visible spectral ranges, where the intrinsic photocatalytic activity of TiO2 nanoparticles or that of ZnO nanoparticles is individually considerably weak For a comparative study, by embedding TiO(2) nanoparticles of ca. 6 nm and ZnO nanoparticles of ca. 40 nm in the sol-gel matrix of acrylic resin, we make thin film coatings of TiO(2)-ZnO nanoparticles (combination of TiO2 and ZnO, each with a mass ratio of 8.5%), as well as the composite films of TiO(2) nanoparticles alone (17.0%), and ZnO nanoparticles alone (17.0%), and a negative control group with no nanoparticles. For all of these thin films coated on polyvinyl chloride (PVC) polyester, we experimentally study photocatalytic activity and systematically measure spectral degradation (recovery obtained by photocatalytic reactions). This spectral characterization exhibits photodegradation levels of the contaminant at different excitation wavelengths (in the range of 310-469 nm) to distinguish different parts of optical spectrum where TiO(2) and ZnO nanopartides are individually and concurrently active. We observe that the photocatalytic activity is significantly improved towards the visible range with the use of TiO(2)-ZnO combination compared to the individual cases. Particularly for the excitation wavelengths of photochemical reactions longer than 400 nm, where the negative control group and ZnO nanoparticles alone yield no observable photodegradation level and TiO2 nanoparticles alone lead to a low photodegradation level of 14%, the synergic combination of TiO(2)-ZnO nanoparticles achieves a photodegradation level as high as 30%. Investigating their scanning electron microscopy (SEM), X-ray diffraction (XRD), and high resolution transmission electron microscopy (HRTEM), we present evidence of the heterostructure, crystallography, and chemical bonding states for the hybrid TiO(2)-ZnO nanocomposite films, in comparison to the films of only TiO(2) nanoparticles, only ZnO nanoparticles, and no nanoparticles.Item Open Access RF-MEMS load sensors with enhanced Q-factor and sensitivity in a suspended architecture(Elsevier, 2010-11-09) Melik, R.; Unal, E.; Perkgoz, N. K.; Puttlitz, C.; Demir, Hilmi VolkanIn this paper, we present and demonstrate RF-MEMS load sensors designed and fabricated in a suspended architecture that increases their quality-factor (Q-factor), accompanied with an increased resonance frequency shift under load. The suspended architecture is obtained by removing silicon under the sensor. We compare two sensors that consist of 195 μm × 195 μm resonators, where all of the resonator features are of equal dimensions, but one's substrate is partially removed (suspended architecture) and the other's is not (planar architecture). The single suspended device has a resonance of 15.18 GHz with 102.06 Q-factor whereas the single planar device has the resonance at 15.01 GHz and an associated Q-factor of 93.81. For the single planar device, we measured a resonance frequency shift of 430 MHz with 3920 N of applied load, while we achieved a 780 MHz frequency shift in the single suspended device. In the planar triplet configuration (with three devices placed side by side on the same chip, with the two outmost ones serving as the receiver and the transmitter), we observed a 220 MHz frequency shift with 3920 N of applied load while we obtained a 340 MHz frequency shift in the suspended triplet device with 3920 N load applied. Thus, the single planar device exhibited a sensitivity level of 0.1097 MHz/N while the single suspended device led to an improved sensitivity of 0.1990 MHz/N. Similarly, with the planar triplet device having a sensitivity of 0.0561 MHz/N, the suspended triplet device yielded an enhanced sensitivity of 0.0867 MHz/N.Item Open Access White emitting CdS quantum dot nanoluminophores hybridized on near-ultraviolet LEDs for high-quality white light generation and tuning(Institute of Physics Publishing Ltd., 2008) Nizamoglu, S.; Mutlugun, E.; Akyuz, O.; Perkgoz, N. K.; Demir, Hilmi Volkan; Liebscher, L.; Sapra, S.; Gaponik N.; Eychmüller A.To generate white light using semiconductor nanocrystal (NC) quantum dots integrated on light emitting diodes (LEDs), multiple hybrid device parameters (emission wavelengths of the NCs and the excitation platform, order of the NCs with different sizes, amount of the different types of NCs, etc) need to be carefully designed and properly implemented. In this study, we introduce and demonstrate white LEDs based on simple device hybridization using only a single type of white emitting CdS quantum dot nanoluminophores on near-ultraviolet LEDs. Here we present their design, synthesis-growth, fabrication and characterization. With these hybrid devices, we achieve high color rendering index (>70), despite using only a single NC type. Furthermore, we conveniently tune their photometric properties including the chromaticity coordinates, correlated color temperature, and color rendering index with the number of hybridized nanoluminophores in a controlled manner.