Browsing by Subject "Unbiased operation"
Now showing 1 - 2 of 2
Results Per Page
Sort Options
Item Open Access Design, fabrication and operation of a very high intensity CMUT transmit array for beam steering applications(Bilkent University, 2020-12) Khan, Talha MasoodSeveral studies have reported airborne ultrasound transmission systems focused on achieving beamforming. However, beam steering and beamforming for capacitive micromachined ultrasonic transducers (CMUTs) at high intensity remains to be accomplished. CMUTs, like other ultrasonic transducers, incorporate a loss mechanism to obtain a wide bandwidth. They are restricted to a limited amount of plate swing due to the gap between the radiating plate and the bottom electrode, along with a high dc bias operation. CMUTs can be designed to produce high-intensity ultrasound by employing an unbiased operation. This mode of operation allows the plate to swing the entire gap without collapsing, thus enabling higher intensity. In this study, we use an equivalent circuit-based model to design unbiased CMUT arrays driven at half the mechanical frequency. This model is cross verified using finite element analysis (FEA). CMUT arrays are produced in multiple configurations using a customized microfabrication process that involves anodic wafer bonding, a single lithographic mask, and a shadow mask. We use impedance measurements to characterize the microfabricated devices. We experimentally obtained the highest reported intensity using a microfabricated 2×2 CMUT array driven at resonance in a pulsed configuration. This array is also capable of beam steering and beamforming at a high intensity such that it can steer the entire half-space. The beam obtained from the array is in excellent agreement with the theoretical predictions. The amplitude and phase compensation for the devices remain constant that makes these arrays attractive for applications involving park assist, gesture recognition, and tactile displays.Item Open Access Electrically unbiased and half frequency driven waterborne 16×16-element 2-D phased array CMUT(Bilkent University, 2019-08) Enhoş, KeremCapacitive micromachined ultrasonic transducers (CMUT) are typically used as arrays consisting of separate cells or interconnected sub arrays, and these cells have several operation modes. Design procedure and measurements have been previously presented for an airborne CMUT cell without a DC bias. In unbiased mode, the plate motion spans the entire gap without collapsing. The frequency of sinusoidal electrical input signal is half of the resulting acoustical output signal. A large plate swing can be obtained at low excitation voltages using the entire remaining gap. In this work, a design procedure of arrays with unbiased operation mode is derived. Designs are validated by means of simulations and measurements on fabricated CMUTs. The problems associated with beamforming are resolved. Use of this operation mode in an array configuration enables larger acoustical power output. A better transmitted signal waveform definition is obtained when pulse width modulation (PWM) is employed. In the design process of CMUTs, large-signal equivalent circuit model is used. In order to have volumetric transmission, a 16×16 (256 elements) phased array configuration is chosen. A design procedure is presented considering the radiation pattern, Rayleigh distance and the parameters of the lumped-element model. This procedure is applied for designing two arrays, with resonance frequencies at 7.5 MHz and at 18.5 MHz. Harmonic balance and transient analyses are carried out with Gaussian enveloped tone burst, transient sinusoidal and PWM signals with different duty cycles. Outputs of these simulations are fed in beamforming toolboxes for further verification. Corresponding experimental measurements are conducted on an ultrasound measurement system. The dimensions of the CMUT elements in the array are determined as 80 μm element radius, 15 μm plate thickness, and 171 nm effective gap height at 7.5 MHz, where the center-to-center inter-element pitch is set at 192 μm. The array is designed such that it has maximum Rayleigh distance of 45.3 mm, while having a maximum sidelobe level of −17.4 dB. According to these specifications, CMUT array is manufactured using wafer scale batch compatible production. Only two lithography masks, which require conventional photolithography steps, are used in production. The vibrating plate is constructed with anodic wafer bonding and the fabricated CMUT array chip is integrated to PCB with flip-chip bonding. Measurements are conducted for this novel device by integrating the CMUT array chip manufactured with MEMS techniques and conventional macro scale manufactured PCB by using impedance analyser.