Browsing by Subject "Substrates"

Now showing 1 - 20 of 37

Open Access
Analysis of Fe nanoparticles using XPS measurements under d.c. or pulsed-voltage bias
(2010) Süzer, Şefik; Baer, D. R.; Engelhard, M. H.
The impact of solution exposure on the charging properties of oxide coatings on Fe metal-core oxide-shell nanoparticles has been examined by sample biasing during XPS measurements. The Fe nanoparticles were suspended in relatively unreactive acetone and analyzed after particles containing solutions were deposited on SiO2/Si or Au substrates. The particle and substrate combinations were subjected to ±10V d.c. or ±5V a.c., biasing in the form of square wave (SQW) pulses. The samples experienced variable degrees of charging for which low-energy electrons at ∼1eV, 20 μA and low-energy Ar+ ions were used to minimize it. Application of d.c. bias and/or SQW pulses significantly influences the extent of charging, which is utilized to gather additional analytical information about the sample under investigation. This approach allows separation of otherwise overlapping peaks. Accordingly, the O1s peaks of the silicon oxide substrate, the iron oxide nanoparticles, and that of the casting solvent can be separated from each other. Similarly, the C1s peak belonging to the solvent can be separated from that of the adventitious carbon. The charging shifts of the iron nanoparticles are strongly influenced by the solvent to which the particles were exposed. Hence, acetone exhibited the largest shift, water the smallest, and methanol in between. Dynamical measurements performed by application of the voltage stress in the form of SQW pulses provides information about the time constants of the processes involved, which leads us to postulate that these charging properties we probe in these systems stem mainly from ionic movement(s).
Open Access
Analytic modeling of patterned high-Tc superconductive bolometers: film and substrate interface effects
(SPIE, 1998) Fardmanesh, Mehdi; Rothwarf, A.
Superconducting film and substrate interface effects on the response of superconductive edge-transition bolometers are modeled with a one dimensional thermal model in closed form, for samples with large area patterns compared to the substrate thickness. The results from the model agree with experimental results on samples made of meander line patterned granular YBCO films on crystalline substrates, in both the magnitude and phase of the response versus modulation frequency up to about 100 KHz, the limit of the characterization setup. Using the fit of the calculated frequency response curves obtained from the model to the measured ones, values of the film-substrate and substrate-holder thermal boundary resistance, heat capacity of the superconducting film, and the thermal parameters of the substrate materials could be investigated. While the calculated magnitude and phase of the response of the SrTiO3 substrate samples obtained from the model is in a very good agreement with the measured values, the calculated response of the LaAlO3 and MgO substrate samples deviate slightly from the measured values at very low frequencies, increasing with an increase in the thermal conductivity of the substrate material. Using the fit of the calculated response to the measured values, film-substrate thermal boundary resistances in the range of 4.4* 10-3 to 4.4* 10-2 K-cm2-w-1 are obtained for different substrate materials. The effect of substrate optical absorption in the response of the samples is also investigated.
Open Access
Applications of hybrid discrete Fourier transform moment method to the fast analysis of large rectangular dipole arrays printed on a thin grounded dielectric substrate
(Wiley, 2002) Chou, H.-T.; Ho, H.-K.; Civi, O. A.; Erturk, V. B.
Recently a discrete Fourier transform-method of moments (DFT-MoM) scheme was developed for fast analysis of electrically large rectangular planar dipole arrays, which has been shown to be very efficient in terms of number reduction of unknown variables and computational complexity. The applications of this DFT-MoM to treat dipole arrays printed on a grounded dielectric substrate are examined in this Letter. Numerical results are presented to validate its efficiency and accuracy.
Open Access
An array of surface-enhanced Raman scattering substrates based on plasmonic lenses
(Wiley, 2012-10-01) Kahraman, M.; Cakmakyapan, S.; Özbay, Ekmel; Culha, M.
An array of ring-shaped holes is prepared from silver thin films using electron beam lithography. The optimal conditions for high performance as a surface-enhanced Raman scattering (SERS) substrate are investigated. Either the diameter of the hole (0.5, 1.0, 2.0, 3.0 and 4.0 μm) or the slit width (200, 300, 400, 500 and 600 nm) is varied. 4-Aminothiophenol (ATP) adsorbed on the structures as a self-assembled monolayer (SAM) is used as probe to evaluate the SERS performance of the generated structures. It is found that there is an optimal configuration for ring-shaped holes with a 3.0-μm diameter and 200-nm slit width. The SERS activity on this optimal lens configuration is found to be 13 times greater than that of the activity on the silver thin film. An array of these structures at this optimal configuration can easily be constructed and used in a range of SERS-based sensing applications. An array of ring-shaped holes is prepared from silver thin films using electron beam lithography. The optimal conditions for high performance as a surface-enhanced Raman scattering (SERS) substrate are investigated. It is found that there is an optimal configuration for ring-shaped holes with a 3.0-μm diameter and 200-nm slit with. The SERS activity on this optimal lens configuration is found to be 13 times greater than that of the activity on the silver thin film.
Open Access
A baseball-bat-like CdTe/TiO2 nanorods-based heterojunction core–shell solar cell
(Elsevier, 2013) Karaagac, H.; Parlak, M.; Aygun, L. E.; Ghaffari, M.; Bıyıklı, Necmi; Okyay, Ali Kemal
Rutile TiO2 nanorods on fluorine-doped thin oxide glass substrates via the hydrothermal technique were synthesized and decorated with a sputtered CdTe layer to fabricate a core-shell type n-TiO2/p-CdTe solar cell. Absorbance spectrum verified the absorption contribution of both TiO2 and CdTe to the absorption process. The solar cell parameters, such as open circuit voltage, short circuit current density, fill factor and power conversion efficiency were found to be 0.34 V, 1.27 mA cm-2, 28% and 0.12%, respectively. .
Open Access
Concentric ring structures as efficient SERS substrates
(Institute of Electrical and Electronics Engineers, 2013) Cinel, N. A.; Cakmakyapan, S.; Ertas, G.; Özbay, Ekmel
Plasmonic nanopatterned structures that can work as highly efficient surface-enhanced Raman scattering (SERS) substrates are presented in this study. A 'coupled' concentric ring structure has been designed, fabricated, tuned, and compared to an 'etched' concentric ring structure and plain gold film via SERS experiments. The proposed design gives Raman signal intensity 630 times larger than plain gold film and 8 times larger than an 'etched' concentric ring structure. The surface plasmons were imaged with the fluorescence imaging technique and supporting numerical simulations were done.
Open Access
Differential charging in SiO2/Si systems as determined by XPS
(American Chemical Society, 2004) Karadas, F.; Ertas, G.; Süzer, Şefik
The Si2p binding and the SiKLL kinetic energy difference between the SiO2 layer and Si substrate is shown to be influence by application of external voltage bias to the sample holder due to the differential charging as was already reported earlier (Ulgut, B.; Suzer, S. J. Phys. Chem. B 2003, 107, 2939). The cause of this bias induced (physical)-shift is now proven to be mostly due to partial neutralization by the stray electrons within the vacuum system by (i) introducing additional stray electrons via a filament and following their influence on the measured binding energy as a function of the applied voltage, (ii) measuring and Auger parameter. It is also shown that citrate-capped gold nanoclusters deposited on the SiO2/Si system experience differential charging similar to that of the oxide layer rather than the silicon substrate.
Open Access
Effect of substrate temperature and Ga source precursor on growth and material properties of GaN grown by hollow cathode plasma assisted atomic layer deposition
(IEEE, 2016) Haider, Ali; Kizir, Seda; Deminskyi, P.; Tsymbalenko, Oleksandr; Leghari, Shahid Ali; Bıyıklı, Necmi; Alevli, M.; Gungor, N.
GaN thin films grown by hollow cathode plasma-assisted atomic layer deposition (HCPA-ALD) at two different substrate temperatures (250 and 450 °C) are compared. Effect of two different Ga source materials named as trimethylgallium (TMG) and triethylgallium (TEG) on GaN growth and film quality is also investigated and reviewed. Films were characterized by X-ray photoelectron spectroscopy, spectroscopic ellipsometery, and grazing incidence X-ray diffraction. GaN film deposited by TMG revealed better structural, chemical, and optical properties in comparison with GaN film grown with TEG precursor. When compared on basis of different substrate temperature, GaN films grown at higher substrate temperature revealed better structural and optical properties.
Open Access
Flexible metamaterials for wireless strain sensing
(American Institute of Physics, 2009-11-04) Melik, R.; Unal, E.; Perkgoz, N. K.; Puttlitz, C.; Demir, Hilmi Volkan
We proposed and demonstrated flexible metamaterial-based wireless strain sensors that include arrays of split ring resonators (SRRs) to telemetrically measure strain. For these metamaterial sensors, we showed that a flexible substrate (e.g., Kapton tape) delivers greater sensitivity and a more linear response as compared to using silicon substrates. Specifically, these tape-based flexible SRR sensors exhibit a significantly improved sensitivity level of 0.292 MHz/kgf with a substantially reduced nonlinearity error of 3% for externally applied mechanical loads up to 250 kgf. These data represent a sixfold increase in sensitivity and a 16-fold reduction in error percentage.
Open Access
Fundamentals, progress, and future directions of nitride-based semiconductors and their composites in two-dimensional limit: a first-principles perspective to recent synthesis
(American Institute of Physics Inc., 2018) Kecik D.; Onen, A.; Konuk, M.; Gürbüz, E.; Ersan, F.; Cahangirov, S.; Aktürk, E.; Durgun, Engin; Çıracı, Salim
Potential applications of bulk GaN and AlN crystals have made possible single and multilayer allotropes of these III-V compounds to be a focus of interest recently. As of 2005, the theoretical studies have predicted that GaN and AlN can form two-dimensional (2D) stable, single-layer (SL) structures being wide band gap semiconductors and showing electronic and optical properties different from those of their bulk parents. Research on these 2D structures have gained importance with recent experimental studies achieving the growth of ultrathin 2D GaN and AlN on substrates. It is expected that these two materials will open an active field of research like graphene, silicene, and transition metal dichalcogenides. This topical review aims at the evaluation of previous experimental and theoretical works until 2018 in order to provide input for further research attempts in this field. To this end, starting from three-dimensional (3D) GaN and AlN crystals, we review 2D SL and multilayer (ML) structures, which were predicted to be stable in free-standing states. These are planar hexagonal (or honeycomb), tetragonal, and square-octagon structures. First, we discuss earlier results on dynamical and thermal stability of these SL structures, as well as the predicted mechanical properties. Next, their electronic and optical properties with and without the effect of strain are reviewed and compared with those of the 3D parent crystals. The formation of multilayers, hence prediction of new periodic layered structures and also tuning their physical properties with the number of layers are other critical subjects that have been actively studied and discussed here. In particular, an extensive analysis pertaining to the nature of perpendicular interlayer bonds causing planar GaN and AlN to buckle is presented. In view of the fact that SL GaN and AlN can be fabricated only on a substrate, the question of how the properties of free-standing, SL structures are affected if they are grown on a substrate is addressed. We also examine recent works treating the composite structures of GaN and AlN joined commensurately along their zigzag and armchair edges and forming heterostructures, δ-doping, single, and multiple quantum wells, as well as core/shell structures. Finally, outlooks and possible new research directions are briefly discussed. © 2018 Author(s).
Open Access
Initial stages of SiGe epitaxy on Si(001) studied by scanning tunneling microscopy
(Elsevier BV, 1995) Oral, A.; Ellialtioglu, R.
We have studied the initial stages of strained SiGe alloy growth on the Si(001)-(2 × 1) surface by scanning tunneling microscopy. The Si0.36Ge0.64 alloy was grown on the silicon substrate at various coverages (0.13-3.6 ML) and at different temperatures (∼ 310-470°C). The growth was one dimensional, preferring the direction perpendicular to the underlying silicon dimer rows at low coverages and low temperatures. Anti-phase boundaries were observed to lead multi-layer growth. Strong interaction between the overlayer and the substrate was found to buckle the substrate as well as SiGe dimers. Different growth mechanisms, island formation and step flow, were identified at low and high substrate temperatures. (2 × n) ordering of the strained overlayer was only observed at an intermediate growth temperature (∼ 390°C). © 1995.
Open Access
Investigation of the effect of thermal cycling on the device performance of YBa2Cu3O7-δ DC-SQUIDs
(2007) Avci I.; Algul, B.P.; Bozbey, A.; Akram, R.; Tepe, M.; Abukay, D.
We investigated the effect of thermal cycling on the operational performance of YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (DC-SQUIDs) fabricated onto 24°SrTiO3 (STO) bicrystal substrates. The devices under investigation consist of directly coupled DC-SQUID magnetometer configurations. Thin films having 200nm thicknesses were deposited by dc-magnetron sputtering and device patterns were made by a standard lithography process and chemical etching. The SQUIDs having 4νm-wide grain boundary Josephson junctions (GBJJs) were characterized by means of critical currents, peak-to-peak output voltages and noise levels, depending on the thermal cycles. In order to achieve a protective layer for the junctions against the undesired effects of thermal cycles and ambient atmosphere during the room temperature storage, the devices were coated with a 400nm thick YBCO layer at room temperature. Since the second layer of amorphous YBCO is completely electrically insulating, it does not affect the operation of the junctions and pick-up coils of magnetometers. This two-layered configuration ensures the protection of the junctions from ambient atmosphere as well as from the effect of water molecules interacting with the film structure during each thermal cycle. © IOP Publishing Ltd.
Open Access
Lyotropic liquid-crystalline mesophase of lithium triflate-nonionic surfactant as gel electrolyte for graphene optical modulator
(American Chemical Society, 2023) Balci, F. M.; Balci, S.; Kocabas, C.; Dag, Ö.
Lithium salt (noncoordinating anions, such as lithium triflate (Ltf)) gel electrolytes may be key for the practical use of electrochemical devices. We introduce a new lyotropic liquid-crystalline (LLC) mesophase using Ltf, a small amount of water (as low as 1.3 water per Ltf), and nonionic surfactant (C18H37(OCH2CH2)10OH, C18E10). The LLC phase forms over a broad range of Ltf/C18E10 mole ratios, 2-18. The clear ethanol solution of the ingredients can be either directly spin-coated over a glass substrate to form a gel phase or it can be prepared as a gel by mixing Ltf, water, and C18E10. The mesophase leaches out surfactant molecules at low salt concentrations, but at a salt/surfactant mole ratio of above 8, the phase is homogeneous with a cubic mesostructure, fully transparent in the visible optical region, mechanically flexible, and an effective gel electrolyte. We have observed a large electrostatic doping on graphene with the Fermi energy level of ∼1.0 eV using Ltf-C18E10 gel electrolytes. The Ltf-based gels demonstrate better properties than commonly used ionic liquid electrolyte in graphene optical modulators. The stability of the new gel electrolytes and their superior performance make them suitable electrolytes for use in graphene-based optical modulators.
Open Access
Modeling the effect of subsurface interface defects on contact stiffness for ultrasonic atomic force microscopy
(AIP Publishing LLC, 2004) Sarioglu, A. F.; Atalar, Abdullah; Degertekin, F. L.
We present a model predicting the effects of mechanical defects at layer interfaces on the contact stiffness measured by ultrasonic atomic force microscopy sAFMd. Defects at subsurface interfaces result in changes at the local contact stiffness between the AFM tip and the sample. Surface impedance method is employed to model the imperfections and an iterative algorithm is used to calculate the AFM tip-surface contact stiffness. The sensitivity of AFM to voids or delaminations and disbonds is investigated for film-substrate combinations commonly used in microelectronic structures, and optimum defect depth for maximum sensitivity is defined. The effect of contact force and the tip properties on the defect sensitivity are considered. The results indicate that the ultrasonic AFM should be suitable for subsurface detection and its defect sensitivity can be enhanced by adjusting the applied force as well as by judicious choice of the AFM tip material and geometry.
Open Access
Modulation behaviors, conductivities, and carrier dynamics of single and multilayer graphenes
(IEEE Computer Society, 2019) Kaya, E.; Kakenov, Nurbek; Kocabaş, Coşkun; Altan, H.; Esentürk, O.
Time domain and time resolved terahertz studies of single- and multi-layer graphene (SLG and MLG) samples and modulator devices will be presented. A high performance up to 100% of modulators were observed with the devices even at very low voltages. High modulation depth over such a broad spectrum and simple device structure brings significant importance toward application of this type of device in THz and related technologies. In addition, conductivities of SLG and MLG devices were also investigated and a change in behavior was observed as the layer thickness increased. The charge carriers dynamics of the samples with pulp fluence and color was also highly interesting.
Open Access
Molecular scale buckling mechanics in individual aligned single-wall carbon nanotubes on elastomeric substrates
(American Chemical Society, 2008) Khang, D. -Y.; Xiao, J.; Kocabaş, Coşkun; MacLaren, S.; Banks, T.; Jiang, H.; Huang, Y. Y.; Rogers, J. A.
We have studied the scaling of controlled nonlinear buckling processes in materials with dimensions in the molecular range (i.e., ∼1 nm) through experimental and theoretical studies of buckling in individual single-wall carbon nanotubes on substrates of poly(dimethylsiloxane). The results show not only the ability to create and manipulate patterns of buckling at these molecular scales, but also, that analytical continuum mechanics theory can explain, quantitatively, all measurable aspects of this system. Inverse calculation applied to measurements of diameterdependent buckling wavelengths yields accurate values of the Young’s moduli of individual SWNTs. As an example of the value of this system beyond its use in this type of molecular scale metrology, we implement parallel arrays of buckled SWNTs as a class of mechanically stretchable conductor.
Open Access
Nanoscale tribology of graphene grown by chemical vapor deposition and transferred onto silicon oxide substrates
(Cambridge University Press, 2016) Demirbaş, T.; Baykara, M. Z.
We present a comprehensive nanoscale tribological characterization of single-layer graphene grown by chemical vapor deposition (CVD) and transferred onto silicon oxide (SiO2) substrates. Specifically, the nanotribological properties of graphene samples are studied via atomic force microscopy (AFM) under ambient conditions using calibrated probes, by measuring the evolution of friction force with increasing normal load. The effect of using different probes and post-transfer cleaning procedures on frictional behavior is evaluated. A new method of quantifying lubrication performance based on measured friction coefficient ratios of graphene and SiO2 is introduced. A comparison of lubrication properties with mechanically-exfoliated graphene is performed. Results indicate that CVD-grown graphene constitutes a very good solid lubricant on SiO2, reducing friction coefficients by ∼ 90% for all investigated samples. Finally, the effect of wrinkles associated with CVD-grown graphene on measured friction values is quantitatively analyzed, with results revealing a substantial increase in friction on these structural defects.
Open Access
Newly designed silver coated-magnetic, monodisperse polymeric microbeads as SERS substrate for low-level detection of amoxicillin
(Elsevier, 2016-09) Kibar, G.; Topal, A. E.; Dana, A.; Tuncel, A.
We report the preparation of silver-coated magnetic polymethacrylate core-shell nanoparticles for use in surface-enhanced Raman scattering based drug detection. Monodisperse porous poly (mono-2-(methacryloyloxy)ethyl succinate-co-glycerol dimethacrylate), poly (MMES-co-GDMA) microbeads of ca. 5 μm diameter were first synthesized through a multistage microsuspension polymerization technique to serve as a carboxyl-bearing core region. Microspheres were subsequently magnetized by the co-precipitation of ferric ions, aminated through the surface hydroxyl groups and decorated with Au nanoparticles via electrostatic attraction. An Ag shell was then formed on top of the Au layer through a seed-mediated growth process, resulting in micron-sized monodisperse microbeads that exhibit Raman enhancement effects due to the roughness of the Ag surface layer. The core-shell microspheres were used as a new substrate for the detection of amoxicillin at trace concentrations up to 10-8 M by SERS. The proposed SERS platform can be evaluated as a useful tool for the follow-up amoxicillin pollution and low-level detection of amoxicillin in aqueous media.
Open Access
Plasmonic absorbers for multispectral and broadband absorption
(SPIE, 2012) Ayaş, Sencer; Güner, Hasan; Türker, Burak; Ekiz, Öner; Dana, Aykutlu
We present polarization dependent multispectral and broadband plasmonic absorbers in the visible spectrum. The spectral characteristics of these structures are tunable over a broad spectrum. Experimental results are verified with the FDTD and RCWA analysis methods. These structures are used as surface enhanced raman spectroscopy(SERS) substrates. Designed structures have resonances that span the Raman Stokes and excitation wavelength. Such structures can be used for energy, LED and other spectroscopy applications. © 2012 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).
Open Access
Response of polyelectrolyte layers to the SiO2 substrate charging as probed by XPS
(2009) Conger, C. P.; Süzer, Şefik
A single layer of the Cationic polyelectrolyte poly(allyamine) hydrochloride (PAH) deposited, using the layer-by-layer technique, on a silicon substrate containing 5 nm oxide layer is investigated by XPS while applying an external potential bias to the sample to control and manipulate the charge built-up on the oxide layer. Under application of a -10 V bias, the oxide layer is positively charged due to Photoemission process, evidenced by the measured Si2p binding energy of 104.4 eV. Application of a +10 V bias attracts the low energy neutralizing electrons, stemming from a hot filament, and leads to a negatively charged oxide layer, also evidenced by the measured Si2p binding energy of 102.9 eV. The single polyelectrolyte overlayer also responds to this polarity change of the oxide layer underneath by displaying a somewhat larger shifts both in the C1s and Nls peaks. In addition to the shifts in the positions, the N1s peaks undergo a significant intensity depletion, mostly on the positively charged -N+ component. We interpret this intensity depletion to be the result of reorientation of some of the dangling positively charged groups by moving toward the negatively charged oxide underlayer. To our knowledge this is the first time that a chemically specific response to an electrical stimuli is reported using XPS. A bilayer LbL film consisting of PAH and PSS, exhibits even a larger charging shift, but this time no intensity alteration is observed, most probably due to locking of the -N+ groups by the -SO3 + counterions of the second layer. © 2009 American Chemical Society.