Browsing by Subject "Raman"
Now showing 1 - 5 of 5
Results Per Page
Sort Options
Item Open Access Ceria promoted NOx storage and reduction materials(2011) Say, ZaferIn the current work, the effect of CeO2 promotion on the NOx storage materials and NOx storage-reduction (NSR) catalysts is studied. Synthesized materials were prepared using different baria and ceria loadings in order to investigate the influence of the surface composition on the NOx storage process. Synthesized materials were also thermally treated in the temperature range within 300 - 1273 K to mimic the thermal aging effects on the material structure. Structural properties of the synthesized materials were investigated via spectroscopic and diffraction techniques such as Raman spectroscopy, X-ray diffraction (XRD), and BET (Brunauer, Emmett, ve Teller) surface area analysis. These ex-situ characterization studies revealed that materials containing Pt showed indications of sintering after thermal treatment at elevated temperatures where Pt sites grew in size and were partially covered by BaO domains. Pt addition to the BaO/Al2O3 system facilitated the formation of the undesired BaAl2O4 phase, particularly at high baria loadings. Decomposition of the Ba(NO3)2 species took place at lower temperatures for Pt containing materials. An indication for a strong-metal-support interaction (SMSI) between Pt and CeO2 sites was observed in Raman spectroscopic data, resulting in the formation of a new mixed oxide phase on the surface. BET results indicated that the specific surface area (SSA) of the synthesized materials monotonically decreased with increasing temperature and increasing BaO and CeO2 loadings. The behavior of the synthesized materials in NOx and SOx adsorption experiments were also investigated via temperature programmed desorption (TPD) and in-situ Fourier transform infrared (FTIR) spectroscopy. Ceria promotion had no significant influence on the nature of the adsorbed nitrate species and the NOx uptake ability of the alumina support material. On the other hand, addition of Pt to CeO2/Al2O3 binary and BaO/CeO2/Al2O3 ternary systems was observed to enhance the NOx storage. For the ternary mixed oxide NOx storage systems (BaO/CeO2/Al2O3), increasing BaO or CeO2 loadings results in a decrease in the specific surface area values, which in turn leads to decreasing NOx uptake. SO2 (g) + O2 (g) interaction with a selected set of samples were also investigated via in-situ FTIR spectroscopy. These experiments reveal that ceria promotion and platinum addition assisted the formation of surface sulfate species. Furthermore, the presence of ceria also resulted in a decrease in the thermal stability of sulfates and enabled easier regeneration.Item Open Access Gold catalysts supported on ceria doped by rare earth metals for water gas shift reaction: influence of the preparation method(2009) Andreeva, D.; Ivanov, I.; Ilieva, L.; Abrashev, M. V.; Zanella, R.; Sobczak, J. W.; Lisowski, W.; Kantcheva, M.; Avdeev, G.; Petrov, K.Gold catalysts based on ceria, doped by various RE metals (La, Sm, Gd, Yb, Y) were studied. The influence of the preparation methods on structure, properties and catalytic activity in the WGS reaction was investigated. The catalysts' supports were prepared using two different methods: co-precipitation (CP) and mechanochemical activation (MA). The catalysts were tested in a wide temperature interval without and after reactivation. All samples were characterized using a combination of X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM), Raman spectroscopy (RS) and X-ray photoelectron spectroscopy (XPS) and TPR. It was found that the catalytic activity of MA catalysts is higher than CP ones. The gold catalysts based on ceria doped by Yb and Sm exhibited the highest activity. After reactivation in air the MA samples almost kept the WGS activity same, while the CP catalysts increased it. The catalysts of a single- and double-phase structure are formed as a result of CP and MA preparation, respectively. There are no big differences in the gold particles size (2-3 nm) depending on dopants and on the preparation techniques. The RS spectra analysis indicates that most probably the oxygen vacancies are adjacent to Me3+ dopant and the ceria structure seems to be better ordered than in the case of alumina as a dopant. There is no distinct correlation between reducibility and WGS activity. The XPS analysis disclose positively charged gold particles in addition to metallic gold within a surface region of fresh samples and only metallic gold on the samples after catalytic processing. There is no simple correlation between the concentration of Ce3+ in the samples and their WGS activity.Item Open Access Nanomechanical strain testing of low dimensional materials with micro-electro mechanical system (MEMS) chips(2023-09) Başcı, UğurThis thesis explores nanomechanical strain testing of low-dimensional materials. The limitations of existing experimental environments for testing low-dimensional materials are discussed. To overcome these limitations, the study proposes the use of self-designed Micro-Electro Mechanical Systems (MEMS) chips. The fabrication methods and advantages of MEMS chips are explained. The investigation involves studying few-layer 2H-MoS2 crystals using MEMS chips. Device preparation techniques, such as mechanical exfoliation and all-dry transfer, are outlined. Raman measurements are conducted on MoS2 to analyze its response to strain, specifically focusing on the E12g mode Raman peak. The piezoelectric properties of MoS2 are extensively discussed, including piezo voltage-resistivity and IV mea-surements. An interesting thermoelectric bipolar photocurrent response in MoS2 is explored using scanning photocurrent microscopy (SPCM). Possible contributions of different mechanisms such as the Photothermoelectric Effect (PTE) or Flexo-photovoltaic effect of Bipolar Photocurrent response are discussed. The contribution of stress on the recently shown substrate effect is tested in this work. The growth and transfer optimization of V2O3 crystals which have a strain-dependent phase transition properties is explored, with a focus on adapting growth to a conventional CVD chamber. Polymer-assisted transfer techniques and passivation methods are investigated. Raman spectroscopy results demon-strate a shift in the Raman spectrum, and completed V2O3 MEMS devices are showcased. In addition, some preliminary work upon V2O3 growth in different substrates (Mica) is tested. Finally, some small top-gate modulations of V2O3 exploiting Metal-insulator transition property is shown. Overall, this thesis contributes to the field of nanomechanical strain testing of low-dimensional materials by introducing MEMS chips as an effective experimental platform. The investigations provide valuable insights into the mechanism of the substrate-engineered photocurrent generation analysis of 2H-MoS2. The thesis also provides a device fabrication methodology to study interesting phase transitions in strongly-correlated materials. These findings have implications for understanding the properties and potential applications of low-dimensional materials.Item Open Access Novel one-step synthesis of silica nanoparticles from sugarbeet bagasse by laser ablation and their effects on the growth of freshwater algae culture(Elsevier, 2014) San, N. O.; Kurşungöz, C.; Tümtaş, Y.; Yaşa, Ö.; Ortac, B.; Tekinay, T.Scientific research involving nanotechnology has grown exponentially and has led to the development of engineered nanoparticles (NPs). Silica NPs have been used in numerous scientific and technological applications over the past decade, necessitating the development of efficient methods for their synthesis. Recent studies have explored the potential of laser ablation as a convenient way to prepare metal and oxide NPs. Due to its high silica content, low cost, and widespread availability, sugarbeet bagasse is highly suitable as a raw material for producing silica NPs via laser ablation. In this study, two different NP production methods were investigated: laser ablation and NaOH treatment. We developed a novel, one-step method to produce silica NPs from sugarbeet bagasse using laser ablation, and we characterized the silica NPs using environmental scanning electron microscopy (ESEM), energy dispersive spectrometry (EDS), dynamic light scattering (DLS), transmission electron microscopy (TEM), attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. EDS analysis and XPS confirmed the presence of silica NPs. The NPs produced by laser ablation were smaller (38-190 nm) than those produced by NaOH treatment (531-825 nm). Finally, we demonstrated positive effects of silica NPs produced from laser ablation on the growth of microalgae, and thus, our novel method may be beneficial as an environmentally friendly procedure to produce NPs.Item Open Access Strain-reduced micro-LEDs grown directly using partitioned growth(Frontiers Media S.A., 2021-03-10) Lu, S.; Zhang, Y.; Zhang, Z.-H.; Tsai, P. C.; Zhang, X.; Zhang, S. T.; Demir, Hilmi VolkanStrain-reduced micro-LEDs in 50 μm × 50 μm, 100 μm × 100 μm, 200 μm × 200 μm, 500 μm × 500 μm, and 1,000 μm × 1,000 μm sizes were grown on a patterned c-plane sapphire substrate using partitioned growth with the metal-organic chemical-vapor deposition (MOCVD) technique. The size effect on the optical properties and the indium concentration for the quantum wells were studied experimentally. Here, we revealed that the optical properties can be improved by decreasing the chip size (from 1,000 to 100 µm), which can correspondingly reduce the in-plane compressive stress. However, when the chip size is further reduced to 50 μm × 50 μm, the benefit of strain release is overridden by additional defects induced by the higher indium incorporation in the quantum wells and the efficiency of the device decreases. The underlying mechanisms of the changing output power are uncovered based on different methods of characterization. This work shows the rules of thumb to achieve optimal power performance for strain-reduced micro-LEDs through the proposed partitioned growth process.