Browsing by Subject "Microfluidic chip"

Now showing 1 - 4 of 4

Open Access
3D modeling of on-chip acoustophoretic particle manipulation in a polymer microfluidic device
(Chemical and Biological Microsystems Society, 2016) Çaǧatay, E.; Özer, M. B.; Çetin, Barbaros
This study focuses on understanding of the sensitivities of the acoustophoretic process on uncertainties/errors in the geometric properties of the chip material and the piezoelectric actuators. The sensitivity of the acoustophoretic process is investigated both numerically and experimentally. For the numerical simulations a three dimensional finite element model is used. In the experimental analysis, a microfluidic chip with two stations is used. The first station has the accurate geometric values of the design and the second station has the introduced error in a geometric parameter so that the effect of this error can be demonstrated on the same chip and the channel.
Open Access
Alternative screening method for analyzing the water samples through an electrical microfluidics chip with classical microbiological assay comparison of P. aeruginosa
(Elsevier, 2020) Bilican, İsmail; Bahadır, T.; Bilgin, K.; Güler, Mustafa Tahsin
Pseudomonas aeruginosa is a pathogenic bacterium in fresh water supplies that creates a risk for public health. Microbiological analysis of drinking water samples is time consuming and requires qualified personnel. Here we offer a screening system for rapid analysis of spring water that has the potential to be turned into a point-of-need system by means of simple mechanism. The test, which takes 1 h to complete, electrically interrogates the particles through a microfluidic chip suspended in the water sample. We tested the platform using water samples with micro beads and water samples spiked with P. aeruginosa at various concentrations. The mono disperse micro beads were used to evaluate the performance of the system. The results were verified by the gold standard membrane filtration method, which yielded a positive test result only for the P. aeruginosa spiked samples. Detection of 0–11 k bacteria in 30 μL samples was successfully completed in 1 h and compared with a conventional microbiological method. The presented method is a good candidate for a rapid, on-site, screening test that can result in a significant reduction in cost and analysis time compared to microbiological analyses routinely used in practice.
Open Access
Fabricating plasma bonded microfluidic chips by CO2 laser machining of PDMS by the application of viscoelastic particle focusing and droplet generation
(Elsevier Ltd, 2021-11-23) Güler, Mustafa Tahsin
In this study, direct CO2 laser machining of microchannels onto PDMS slabs and plasma bonding for sealing have been shown to provide the fastest method to fabricate PDMS microfluidic chips. Due to resolidification, the ashes and dust remains that cover the PDMS slab surface following this ablation process change the surface chemistry and prevent plasma bonding. Removing these remnants on the surface has been shown to be only possible via attaching and detaching a tape to the surface. The effect of laser frequency, speed and power settings has been investigated over the entire possible range with regards to channel geometry. The best laser settings were determined and the resulting output channels were examined under SEM and optical microscopes. PDMS spin coating after laser machining has been proposed as a pre-treatment process to improve the geometrical features of the channel. Water-in-oil droplet generation in the T-junction, as well as microparticle focusing in viscoelastic fluid – used to sample enrichment– have been shown as examples of applications that benefit from precise direct laser machined microchannels.
Open Access
Low cost, ultra-high throuhput particle counting using inertial microfluidics
(Chemical and Biological Microsystems Society, 2016) Çetin, Barbaros; Kaplan, H.; Durkaya, G.; Kurtuldu, H.
In this work, an ultra-high throughput microfluidic particle counting system is demonstrated. For the particle counting, a low cost custom-design optical hardware is developed. The microfluidic chip utilizes the inertial microfluidics to focus the particles in a certain location which significantly enhanced the optical signal utilized for the quantification of the number concentration. The effect of the particle focusing on the counting performance is demonstrated. The proposed system has a potential to be portable and has a capability to process 10 ml of sample within couple minutes.