Browsing by Subject "Instrumentation"

Now showing 1 - 6 of 6

Open Access
Algebraic reconstraction for 3D magnetic resonance-electrical impedance tomography (MREIT) using one component of magnetic flux density
(Institute of Physics and Engineering in Medicine, 2004) Ider, Y. Z.; Onart, S.
Magnetic resonance-electrical impedance tomography (MREIT) algorithms fall into two categories: those utilizing internal current density and those utilizing only one component of measured magnetic flux density. The latter group of algorithms have the advantage that the object does not have to be rotated in the magnetic resonance imaging (MRI) system. A new algorithm which uses only one component of measured magnetic flux density is developed. In this method, the imaging problem is formulated as the solution of a non-linear matrix equation which is solved iteratively to reconstruct resistivity. Numerical simulations are performed to test the algorithm both for noise-free and noisy cases. The uniqueness of the solution is monitored by looking at the singular value behavior of the matrix and it is shown that at least two current injection profiles are necessary. The method is also modified to handle region-of-interest reconstructions. In particular it is shown that, if the image of a certain xy-slice is sought for, then it suffices to measure the z-component of magnetic flux density up to a distance above and below that slice. The method is robust and has good convergence behavior for the simulation phantoms used.
Open Access
Magnetic resonance electrical impedance tomography (MREIT) based on the solution of the convection equation using FEM with stabilization
(Institute of Physics Publishing, 2012-07-27) Oran, O. F.; Ider, Y. Z.
Most algorithms for magnetic resonance electrical impedance tomography (MREIT) concentrate on reconstructing the internal conductivity distribution of a conductive object from the Laplacian of only one component of the magnetic flux density (∇ 2B z) generated by the internal current distribution. In this study, a new algorithm is proposed to solve this ∇ 2B z-based MREIT problem which is mathematically formulated as the steady-state scalar pure convection equation. Numerical methods developed for the solution of the more general convectiondiffusion equation are utilized. It is known that the solution of the pure convection equation is numerically unstable if sharp variations of the field variable (in this case conductivity) exist or if there are inconsistent boundary conditions. Various stabilization techniques, based on introducing artificial diffusion, are developed to handle such cases and in this study the streamline upwind Petrov-Galerkin (SUPG) stabilization method is incorporated into the Galerkin weighted residual finite element method (FEM) to numerically solve the MREIT problem. The proposed algorithm is tested with simulated and also experimental data from phantoms. Successful conductivity reconstructions are obtained by solving the related convection equation using the Galerkin weighted residual FEM when there are no sharp variations in the actual conductivity distribution. However, when there is noise in the magnetic flux density data or when there are sharp variations in conductivity, it is found that SUPG stabilization is beneficial.
Open Access
Nonlinear modeling of an immersed transmitting capacitive micromachined ultrasonic transducer for harmonic balance analysis
(IEEE, 2010) Oguz, H. K.; Olcum, S.; Senlik, M. N.; Taş, V.; Atalar, Abdullah; Köymen, Hayrettin
Finite element method (FEM) is used for transient dynamic analysis of capacitive micromachined ultrasonic transducers (CMUT) and is particularly useful when the membranes are driven in the nonlinear regime. One major disadvantage of FEM is the excessive time required for simulation. Harmonic balance (HB) analysis, on the other hand, provides an accurate estimate of the steady-state response of nonlinear circuits very quickly. It is common to use Mason's equivalent circuit to model the mechanical section of CMUT. However, it is not appropriate to terminate Mason's mechanical LC section by a rigid piston's radiation impedance, especially for an immersed CMUT. We studied the membrane behavior using a transient FEM analysis and found out that for a wide range of harmonics around the series resonance, the membrane displacement can be modeled as a clamped radiator. We considered the root mean square of the velocity distribution on the membrane surface as the circuit variable rather than the average velocity. With this definition, the kinetic energy of the membrane mass is the same as that in the model. We derived the force and current equations for a clamped radiator and implemented them using a commercial HB simulator. We observed much better agreement between FEM and the proposed equivalent model, compared with the conventional model.
Embargo
On the use of drift correction for electrochemical impedance spectroscopy measurements
(Elsevier, 2023-02-01) Orazem, M.E.; Ulgut, Burak
The effectiveness of drift correction is explored for measurement of electrochemical impedance spectra. Numerical simulations and experimental data for batteries and capacitors are used to show that drift correction cannot generate Kramers–Kronig consistent data for nonstationary systems. Application of drift correction improves, but does not fully recover, the original spectrum that is not corrupted by the drift. Drift correction improved the quality of spectra obtained for stationary systems under galvanostatic modulation, where the change from one frequency to another caused initial transients that corrupted the measurement.
Open Access
Optimization of the gain-bandwidth product of capacitive micromachined ultrasonic transducers
(IEEE, 2005-12) Olcum, S.; Senlik, M. N.; Atalar, Abdullah
Capacitive micromachined ultrasonic transducers (cMUT) have large bandwidths, but they typically have low conversion efficiencies. This paper defines a performance measure in the form of a gain-bandwidth product and investigates the conditions in which this performance measure is maximized. A Mason model corrected with finite-element simulations is used for the purpose of optimizing parameters. There are different performance measures for transducers operating in transmit, receive, or pulse-echo modes. Basic parameters of the transducer are optimized for those operating modes. Optimized values for a cMUT with silicon nitride membrane and immersed in water are given. The effect of including an electrical matching network is considered. In particular, the effect of a shunt inductor in the gain-bandwidth product is investigated. Design tools are introduced, which are used to determine optimal dimensions of cMUTs with the specified frequency or gain response.
Open Access
A photometric investigation of ultra-efficient LEDs with high color rendering index and high luminous efficacy employing nanocrystal quantum dot luminophores
(Optical Society of America, 2009-12-24) Erdem, T.; Nizamoglu, S.; Sun, X. W.; Demir, Hilmi Volkan
We report a photometric study of ultra-efficient light emitting diodes (LEDs) that exhibit superior color rendering index (CRI) and luminous efficacy of optical radiation (LER) using semiconductor quantum dot nanocrystal (NC) luminophores. Over 200 million systematically varied NC-LED designs have been simulated to understand feasible performance in terms of CRI vs. LER. We evaluated the effects of design parameters including peak emission wavelength, full-width-at-half-maximum, and relative amplitudes of each NC color component on LED performance. Warm-white LEDs with CRI >90 and LER >380 lm/W at a correlated color temperature of 3000 K are shown to be achieved using nanocrystal luminophores. (C) 2009 Optical Society of America