Browsing by Subject "High power fiber lasers"

Now showing 1 - 5 of 5

Open Access
1018 nm Yb-doped high-power fiber laser pumped by broadband pump sources around 915 nm with output power above 100 W
(OSA - The Optical Society, 2017) Midilli, Y.; Efunbajo, O. B.; Şimşek, B.; Ortaç, B.
We demonstrate a 1018 nm ytterbium-doped all-fiber laser pumped by tunable pump sources operating in the broad absorption spectrum around 915 nm. In the experiment, two different pump diodes were tested to pump over a wide spectrum ranging from 904 to 924 nm by altering the cooling temperature of the pump diodes. Across this so-called pump wavelength regime having a 20 nm wavelength span, the amplified stimulated emission (ASE) suppression of the resulting laser was generally around 35 dB, showing good suppression ratio. Comparisons to the conventional 976 nm-pumped 1018 nm ytterbium-doped fiber laser were also addressed in this study. Finally, we have tested this system for high power experimentation and obtained 67% maximum optical-to-optical efficiency at an approximately 110 W output power level. To the best of our knowledge, this is the first 1018 nm ytterbium-doped all-fiber laser pumped by tunable pump sources around 915 nm reported in detail.
Open Access
A combinatorial buffered oxide etching method for high-power cladding light stripper
(Institute of Electrical and Electronics Engineers Inc., 2019) Yapar-Yıldırım, Elif; Karatutlu, Ali; Balk, Ekin Teslime; Midilli, Yakup; Ortaç, Bülend
High-power fiber lasers have been applied in many areas due to their advantages such as high beam quality, compact structure, flexibility and high efficiency. However, the absorption of the pump light is limited and a residual pumped light keeps propagating in the cladding. This residual pumped light affects the beam quality and can damage the whole system. Therefore, an efficient removal of excess high-power cladding light is critical for the safe operation of the high-power fiber lasers and high beam quality [1]. Adding a new structure to the cladding of the fiber leading to interrupt total internal reflection in the clad and scatter away the unwanted pump light is the generalized approach for a cladding light stripper (CLS) device fabrication. Also, it is important to scatter all the unwanted light uniformly along the CLS. Etching the fiber for surface damage and recoating the fiber [2] are two general methods for stripping the cladding light [3-5].
Open Access
Doping management for high-power fiber lasers: 100 W, few-picosecond pulse generation from an all-fiber-integrated amplifier
(Optical Society of America, 2012-07-16) Elahi, P.; Yilmaz, S.; Akçaalan, Ö.; Kalaycioğlu, H.; Öktem, B.; Şenel, Ç.; Ilday, F. Ö.; Eken, K.
Thermal effects, which limit the average power, can be minimized by using low-doped, longer gain fibers, whereas the presence of nonlinear effects requires use of high-doped, shorter fibers to maximize the peak power. We propose the use of varying doping levels along the gain fiber to circumvent these opposing requirements. By analogy to dispersion management and nonlinearity management, we refer to this scheme as doping management. As a practical first implementation, we report on the development of a fiber laser-amplifier system, the last stage of which has a hybrid gain fiber composed of high-doped and low-doped Yb fibers. The amplifier generates 100 W at 100 MHz with pulse energy of 1 μJ. The seed source is a passively mode-locked fiber oscillator operating in the all-normaldispersion regime. The amplifier comprises three stages, which are all-fiber-integrated, delivering 13 ps pulses at full power. By optionally placing a grating compressor after the first stage amplifier, chirp of the seed pulses can be controlled, which allows an extra degree of freedom in the interplay between dispersion and self-phase modulation. This way, the laser delivers 4.5 ps pulses with ∼200 kW peak power directly from fiber, without using external pulse compression.
Open Access
Theoretical analysis of doping management
(IEEE, 2013) Gürsel, A. T.; Elahi, Parviz; İlday, F. Ömer; Ozyazici, M.S.
Two opposing requirements, such as thermal load and nonlinear effects are important limitations in rapid progress of high-power fiber laser technologies. Thermal effects, which limit the average power, can be minimized by using low-doped, longer gain fibers, whereas presence of nonlinear effects requires use of high-doped, shorter fibers to maximize the peak power. Proposed solution of the problem is the use of varying doping levels along the gain fiber to circumvent to mitigate the trade-off between thermal load and nonlinear effects. © 2013 The Chamber of Turkish Electrical Engineers-Bursa.
Open Access
Time-and position-dependent modeling of high-power low-repetition-rate Er-Yb-fiber amplifier
(IEEE, 2013) Pavlov, Ihor; Dülgergil, E.; Elahi, Parviz; İlday, F. Ömer
There is rapid progress in the development of high-power fiber lasers due to their robust operation, low cost, high beam quality at high powers. There are various applications, such as laser sensing, LIDAR applications, processing of specific materials, which require robust and high-power pulsed laser sources at 1550 nm with high beam quality. Achievement of high peak power with low repetition rate is challenging due to well-known problems of strong nonlinear effects and amplified spontaneous emission (ASE) build-up between pulses. In order to reach highest efficiency, the design of each stage of amplification should be carefully optimized. Numerical modeling can be a great tool due to the large number of parameters involved [1]. To date, most modeling efforts of fiber amplification have assumed either a lumped gain model for pulse propagation or a distributed, position-dependent gain model for CW signal for computational simplicity. Here, we investigate both time- and position-dependent gain dynamics numerically, which are used to optimize experimental results. © 2013 IEEE.