Browsing by Subject "Frequency modulation"

Filter results by typing the first few letters
Now showing 1 - 4 of 4
  • Thumbnail Image
    ItemOpen Access
    Analytic modeling of patterned high-Tc superconductive bolometers: film and substrate interface effects
    (SPIE, 1998) Fardmanesh, Mehdi; Rothwarf, A.
    Superconducting film and substrate interface effects on the response of superconductive edge-transition bolometers are modeled with a one dimensional thermal model in closed form, for samples with large area patterns compared to the substrate thickness. The results from the model agree with experimental results on samples made of meander line patterned granular YBCO films on crystalline substrates, in both the magnitude and phase of the response versus modulation frequency up to about 100 KHz, the limit of the characterization setup. Using the fit of the calculated frequency response curves obtained from the model to the measured ones, values of the film-substrate and substrate-holder thermal boundary resistance, heat capacity of the superconducting film, and the thermal parameters of the substrate materials could be investigated. While the calculated magnitude and phase of the response of the SrTiO3 substrate samples obtained from the model is in a very good agreement with the measured values, the calculated response of the LaAlO3 and MgO substrate samples deviate slightly from the measured values at very low frequencies, increasing with an increase in the thermal conductivity of the substrate material. Using the fit of the calculated response to the measured values, film-substrate thermal boundary resistances in the range of 4.4* 10-3 to 4.4* 10-2 K-cm2-w-1 are obtained for different substrate materials. The effect of substrate optical absorption in the response of the samples is also investigated.
  • Thumbnail Image
    ItemOpen Access
    Analytic thermal modeling for dc-to-midrange modulation frequency responses of thin-film high-Tc superconductive edge-transition bolometers
    (Optical Society of America, 2001) Fardmanesh, M.
    Thin-film superconductive edge-transition bolometers are modeled with a one-dimensional analytic thermal model with joule heating, film and substrate materials, and the physical interface effects taken into consideration. The results from the model agree well with the experimental results of samples made of large-meander-line Yba2Cu3O7-x films on crystalline SrTiO3, LaAlO3, and MgO substrates up to 100 kHz, the limits of the experimental setup. Compared with the results of the SrTiO3 substrate samples, the results from the model of the LaAlO3 and the MgO substrate samples deviate slightly from the measured values at very low modulation frequencies (below ∼10 Hz). The deviation increases for higher thermal-conductive substrate materials. When the model was used, the substrate absorption and the thermal parameters of the devices could also be investigated. © 2001 Optical Society of America.
  • Thumbnail Image
    ItemOpen Access
    Enhancing higher harmonics of a tapping cantilever by excitation at a submultiple of its resonance frequency
    (American Physical Society, 2005-03) Balantekin, M.; Atalar, Abdullah
    In a tapping-mode atomic force microscope, the frequency spectrum of the oscillating cantilever contains higher harmonics at integer multiples of the excitation frequency. When the cantilever oscillates at its fundamental resonance frequency w 1, the high Q-factor damps the amplitudes of the higher harmonics to negligible levels, unless the higher flexural eigenmodes are coincident with those harmonics. One can enhance the nth harmonic by the Q factor when the cantilever is excited at a submultiple of its resonance frequency (w 1/n). Hence, the magnitude of the nth harmonic can be measured easily and it can be utilized to examine the material properties. We show theoretically that the amplitude of enhanced higher harmonic increases monotonically for a range of sample stiffness, if the interaction is dominated by elastic force.
  • Thumbnail Image
    ItemOpen Access
    A novel STFT implementation for the analysis of non-stationary jammer interference
    (IASTED, 2004) Durak, L.; Arıkan, Orhan; Song, I.
    A novel adaptive short-time Fourier transform (STFT) implementation for the analysis of non-stationary multi-component jammer signals is introduced. The proposed time-frequency distribution is the fusion of optimum STFTs of individual signal components that are based on the recently introduced generalized time-bandwidth product (GTBP) definition. The GTBP optimal STFTs of the components are combined through thresholding and obtaining the individual component support images, which are related with the corresponding GTBP optimal STFTs.