Browsing by Subject "Electron blocking layer"

Now showing 1 - 4 of 4

Open Access
A hole modulator for InGaN/GaN light-emitting diodes
(American Institute of Physics, 2015) Zhang, Z-H.; Kyaw, Z.; Liu W.; Ji Y.; Wang, L.; Tan S.T.; Sun, X. W.; Demir, Hilmi Volkan
The low p-type doping efficiency of the p-GaN layer has severely limited the performance of InGaN/GaN light-emitting diodes (LEDs) due to the ineffective hole injection into the InGaN/GaN multiple quantum well (MQW) active region. The essence of improving the hole injection efficiency is to increase the hole concentration in the p-GaN layer. Therefore, in this work, we have proposed a hole modulator and studied it both theoretically and experimentally. In the hole modulator, the holes in a remote p-type doped layer are depleted by the built-in electric field and stored in the p-GaN layer. By this means, the overall hole concentration in the p-GaN layer can be enhanced. Furthermore, the hole modulator is adopted in the InGaN/GaN LEDs, which reduces the effective valance band barrier height for the p-type electron blocking layer from ∼332meV to ∼294 meV at 80 A/cm2 and demonstrates an improved optical performance, thanks to the increased hole concentration in the p-GaN layer and thus the improved hole injection into the MQWs.
Unknown
Improving hole injection efficiency by manipulating the hole transport mechanism through p-type electron blocking layer engineering
(Optical Society of America, 2014) Zhang, Zi-Hui; Ju, Z.; Liu W.; Tan S.T.; Ji Y.; Kyaw, Z.; Zhang X.; Hasanov N.; Sun, X. W.; Demir, Hilmi Volkan
The p-type AlGaN electron blocking layer (EBL) is widely used in InGaN/GaN light-emitting diodes (LEDs) for electron overflow suppression. However, a typical EBL also reduces the hole injection efficiency, because holes have to climb over the energy barrier generated at the p-AlGaN/p-GaN interface before entering the quantum wells. In this work, to address this problem, we report the enhancement of hole injection efficiency by manipulating the hole transport mechanism through insertion of a thin GaN layer of 1 nm into the p-AlGaN EBL and propose an AlGaN/GaN/AlGaN-type EBL outperforming conventional AlGaN EBLs. Here, the position of the inserted thin GaN layer relative to the p-GaN region is found to be the key to enhancing the hole injection efficiency. InGaN/ GaN LEDs with the proposed p-type AlGaN/GaN/AlGaN EBL have demonstrated substantially higher optical output power and external quantum efficiency.
Open Access
Investigation of p-type depletion doping for InGaN/GaN-based light-emitting diodes
(American Institute of Physics Inc., 2017) Zhang, Y.; Zhang Z.-H.; Tan S.T.; Hernandez-Martinez, P. L.; Zhu B.; Lu S.; Kang, X. J.; Sun, X. W.; Demir, Hilmi Volkan
Due to the limitation of the hole injection, p-type doping is essential to improve the performance of InGaN/GaN multiple quantum well light-emitting diodes (LEDs). In this work, we propose and show a depletion-region Mg-doping method. Here we systematically analyze the effectiveness of different Mg-doping profiles ranging from the electron blocking layer to the active region. Numerical computations show that the Mg-doping decreases the valence band barrier for holes and thus enhances the hole transportation. The proposed depletion-region Mg-doping approach also increases the barrier height for electrons, which leads to a reduced electron overflow, while increasing the hole concentration in the p-GaN layer. Experimentally measured external quantum efficiency indicates that Mg-doping position is vitally important. The doping in or adjacent to the quantum well degrades the LED performance due to Mg diffusion, increasing the corresponding nonradiative recombination, which is well supported by the measured carrier lifetimes. The experimental results are well numerically reproduced by modifying the nonradiative recombination lifetimes, which further validate the effectiveness of our approach.
Open Access
On the hole accelerator for III-nitride light-emitting diodes
(American Institute of Physics Inc., 2016) Zhang Z.-H.; Zhang, Y.; Bi, W.; Geng, C.; Xu S.; Demir, Hilmi Volkan; Sun, X. W.
In this work, we systematically conduct parametric studies revealing the sensitivity of the hole injection on the hole accelerator (a hole accelerator is made of the polarization mismatched p-electron blocking layer (EBL)/p-GaN/p-AlxGa1-xN heterojunction) with different designs, including the AlN composition in the p-AlxGa1-xN layer, and the thickness for the p-GaN layer and the p-AlxGa1-xN layer. According to our findings, the energy that the holes obtain does not monotonically increase as the AlN incorporation in the p-AlxGa1-xN layer increases. Meanwhile, with p-GaN layer or p-AlxGa1-xN layer thickening, the energy that the holes gain increases and then reaches a saturation level. Thus, the hole injection efficiency and the device efficiency are very sensitive to the p-EBL/p-GaN/p-AlxGa1-xN design, and the hole accelerator can effectively increase the hole injection if properly designed.