Browsing by Subject "Carbon fiber reinforced plastics"

Now showing 1 - 4 of 4

Open Access
Drilling thick fabric woven CFRP laminates with double point angle drills
(Elsevier, 2012) Karpat, Y.; Değer, B.; Bahtiyar, O.
Carbon fiber reinforced plastics (CFRPs) have many desirable properties, including high strength-to-weight ratio, high stiffness-to-weight ratio, high corrosion resistance, and low thermal expansion. These properties make CFRP suitable for use in structural components for aerospace applications. Drilling is the most common machining process applied to CFRP laminates, and it is difficult due to the extremely abrasive nature of the carbon fibers and low thermal conductivity of CFRP. It is a challenge for manufacturers to drill CFRP materials without causing any delamination on the work part while also considering the economics of the process. The subject of this study is the drilling of fabric woven type CFRP laminates which are known to be more resistant to delamination than unidirectional type CFRP laminates. The objective of this study is to investigate the influence of double point angle drill geometry on drilling performance through an experimental approach. An uncoated carbide and two diamond coated carbide drills with different drill tip angles are employed in drilling experiments of aerospace quality thick fabric woven CFRP laminates. Force and torque measurements are used to investigate appropriate drilling conditions based on drill geometry and ideal drilling parameters are determined. Tool life tests of the drills were conducted and the condition of the diamond coating is examined as a function of drilling operational parameters. High feed rate drilling experiments are observed to be favorable in terms of drill wear. Feed is observed to be more important than speed, and the upper limit of feed is dictated by the drill design and the rigidity of the machine drill. Hole diameter variation due to drill wear is monitored to determine drill life. At high feeds, hole diameter tolerance is observed to be more critical than hole exit delamination during drilling of fabric woven CFRP laminates.
Open Access
Energy based investigation of process parameters while drilling carbon fiber reinforced polymers
(Elsevier B.V., 2016) Karpat, Yiğit; Bahtiyar, O.
Carbon fiber reinforced polymers (CFRPs) are widely used in the aerospace industry due to their light weight, high strength, and low thermal conductivity. Drilling is a critical process that affects the quality of CFRP parts. This work studies the influence of process parameters on delamination and tool wear. Polycrystalline diamond helical drills are used in the experiments. It has been shown that drilling energy calculations can be used to set appropriate feed and speed parameters and for increasing drilling performance of CFRPs. The results also indicate the importance of thermal modeling of CFRP laminate for better understanding of the drilling process. © 2016 The Authors.
Open Access
Mechanistic force modeling for milling of carbon fiber reinforced polymers with double helix tools
(Elsevier, 2013) Karpat, Y.; Polat, N.
Carbon fiber reinforced polymers (CFRP) have emerged as the material of choice to satisfy increasing demand for lighter aircrafts. Machinability characteristics of CFRPs are quite different than those of metals; therefore, special tool designs have been developed for CFRP machining. The double helix end mill design compresses the upper and lower sides of the laminate using opposite helix angles that eliminate delamination. A mechanistic force model for double helix tools is developed based on milling force data obtained on flat end mills. The proposed model can be used to improve double helix tool designs and to optimize milling process parameters.
Open Access
Milling force modelling of multidirectional carbon fiber reinforced polymer laminates
(Elsevier, 2012) Karpat, Yiğit; Bahtiyar, O.; Deger, B.
Carbon fiber reinforced polymer (CFRP) usage in the aerospace industry has been steadily increasing due to its superior material properties such as high strength, low weight, high resistance to corrosion, and a low thermal expansion coefficient. In addition, CFRP parts are produced near-net-shape, a process that eliminates rough machining operations. However, machining operations such as drilling, side milling, and slotting are still necessary to give the CFRP parts their final shape. A majority of the studies on machining of CFRP laminates are on drilling. The number of studies on milling of CFRPs is quite limited. In this study, a mechanistic cutting force model for milling CFRPs is proposed based on experimentally collected cutting force data during slot milling of unidirectional CFRP laminates using a polycrystalline diamond cutter. Cutting force coefficients in radial and tangential directions are calculated as a function of fiber cutting angle. The mechanistic model is shown to be capable of predicting cutting forces during milling of multidirectional CFRP laminates and capable of investigating stability of machining. © 2012 The Authors.