Browsing by Author "Bahtiyar, O."

Now showing 1 - 8 of 8

Open Access
Comparative analysis of PCD drill designs during drilling of CFRP laminates
(Elsevier, 2015) Karpat, Yiğit; Bahtiyar, O.
As a result of increased use of CFRPs in the aerospace industry, the machining of CFRPs has been studied extensively. The majority of these studies consider drilling of CFRPs, since it is the most common process in the machining of structural parts used in aircraft. It has been shown that drilling process parameters and drill geometry significantly influence the quality of holes. In this study, a systematic approach has been used to compare the influence of drill geometry on process outputs such as drilling forces, torques and tool wear. Custom-made double point angle polycrystalline diamond (PCD) drills from the same manufacturer were used in the experiments. The advantage of this approach is that it eliminates the drill material and edge preparation effects on the experimental measurements, thus helps reveal the influence of drill geometry on the process outputs. The pros and cons of different drill designs are discussed and an appropriate design is identified for the drilling of thick CFRP laminate considered in this study.
Open Access
Drilling thick fabric woven CFRP laminates with double point angle drills
(Elsevier, 2012) Karpat, Y.; Değer, B.; Bahtiyar, O.
Carbon fiber reinforced plastics (CFRPs) have many desirable properties, including high strength-to-weight ratio, high stiffness-to-weight ratio, high corrosion resistance, and low thermal expansion. These properties make CFRP suitable for use in structural components for aerospace applications. Drilling is the most common machining process applied to CFRP laminates, and it is difficult due to the extremely abrasive nature of the carbon fibers and low thermal conductivity of CFRP. It is a challenge for manufacturers to drill CFRP materials without causing any delamination on the work part while also considering the economics of the process. The subject of this study is the drilling of fabric woven type CFRP laminates which are known to be more resistant to delamination than unidirectional type CFRP laminates. The objective of this study is to investigate the influence of double point angle drill geometry on drilling performance through an experimental approach. An uncoated carbide and two diamond coated carbide drills with different drill tip angles are employed in drilling experiments of aerospace quality thick fabric woven CFRP laminates. Force and torque measurements are used to investigate appropriate drilling conditions based on drill geometry and ideal drilling parameters are determined. Tool life tests of the drills were conducted and the condition of the diamond coating is examined as a function of drilling operational parameters. High feed rate drilling experiments are observed to be favorable in terms of drill wear. Feed is observed to be more important than speed, and the upper limit of feed is dictated by the drill design and the rigidity of the machine drill. Hole diameter variation due to drill wear is monitored to determine drill life. At high feeds, hole diameter tolerance is observed to be more critical than hole exit delamination during drilling of fabric woven CFRP laminates.
Open Access
Energy based investigation of process parameters while drilling carbon fiber reinforced polymers
(Elsevier B.V., 2016) Karpat, Yiğit; Bahtiyar, O.
Carbon fiber reinforced polymers (CFRPs) are widely used in the aerospace industry due to their light weight, high strength, and low thermal conductivity. Drilling is a critical process that affects the quality of CFRP parts. This work studies the influence of process parameters on delamination and tool wear. Polycrystalline diamond helical drills are used in the experiments. It has been shown that drilling energy calculations can be used to set appropriate feed and speed parameters and for increasing drilling performance of CFRPs. The results also indicate the importance of thermal modeling of CFRP laminate for better understanding of the drilling process. © 2016 The Authors.
Open Access
Experimental evaluation of polycrystalline diamond tool geometries while drilling carbon fiber-reinforced plastics
(Springer, 2014) Karpat, Y.; Deǧer, B.; Bahtiyar, O.
Polycrystalline diamond (PCD) drills are commonly employed in carbon fiber-reinforced plastic (CFRP) drilling to satisfy hole quality conditions with an acceptable tool life and productivity. Despite their common use in industry, only a small number of studies have been reported on drilling CFRPs with PCD drills. In this study, drilling performances of three different PCD drill designs are investigated experimentally using thrust force, torque, and hole exit quality measurements. Results show that work material properties, drilling conditions, and drill design should all be considered together during the selection of process parameters, and the relationships among these factors are quite complex.
Open Access
A mechanistic approach to investigate drilling of UD-CFRP laminates with PCD drills
(Elsevier, 2014) Karpat, Y.; Bahtiyar, O.; Deǧer, B.; Kaftanoǧlu, B.
Carbon fiber reinforced plastics (CFRPs) possess desirable material properties that satisfy the aerospace industry's high strength to weight ratio objective. Therefore, CFRPs are commonly used in structural parts, either alone or together with aluminum and titanium alloys. Drilling of CFRPs has been studied extensively in the literature in recent years, with special emphasis on process parameters and delamination. This study identifies mechanical properties of uni-directional CFRPs through drilling tests. Drilling of uni-directional CFRP plates with and without pilot holes has been performed, and cutting and edge force coefficients are identified. A polycrystalline diamond (PCD) drill was used in tests since this type of drill is commonly used in practice. Finally, validation tests on multi directional CFRP laminates have been performed and good results have been obtained.
Open Access
Mechanistic force modeling for milling of unidirectional carbon fiber reinforced polymer laminates
(2012-06) Karpat, Yiğit; Bahtiyar, O.; Değer, B.
Carbon fiber reinforced polymer (CFRP) usage in the aerospace industry has been steadily increasing due to its superior material properties such as high strength, low weight, high resistance to corrosion, and a low thermal expansion coefficient. In addition, CFRP parts are produced near-net-shape, a process that eliminates rough machining operations. However, machining operations such as drilling, side milling, and slotting are still necessary to give the CFRP parts their final shape. A majority of the studies on machining of CFRP laminates are on drilling. The number of studies on milling of CFRPs is quite limited. In this study, a mechanistic cutting force model for milling CFRPs is proposed based on experimentally collected cutting force data during slot milling of unidirectional CFRP laminates using two different polycrystalline diamond cutters. Cutting force coefficients in radial and tangential directions are calculated as a function of fiber cutting angle. The relationship is represented with simple sine functions. The mechanistic model is shown to be capable of predicting cutting forces during milling of multidirectional CFRP laminates. The experimental milling force measurements and predicted milling forces agree well with each other. Surface milling experiments were also conducted to investigate the relationship between milling forces and surface quality. Some suggestions on surface milling of CFRP laminates are given based on these observations.
Open Access
Milling force modelling of multidirectional carbon fiber reinforced polymer laminates
(Elsevier, 2012) Karpat, Yiğit; Bahtiyar, O.; Deger, B.
Carbon fiber reinforced polymer (CFRP) usage in the aerospace industry has been steadily increasing due to its superior material properties such as high strength, low weight, high resistance to corrosion, and a low thermal expansion coefficient. In addition, CFRP parts are produced near-net-shape, a process that eliminates rough machining operations. However, machining operations such as drilling, side milling, and slotting are still necessary to give the CFRP parts their final shape. A majority of the studies on machining of CFRP laminates are on drilling. The number of studies on milling of CFRPs is quite limited. In this study, a mechanistic cutting force model for milling CFRPs is proposed based on experimentally collected cutting force data during slot milling of unidirectional CFRP laminates using a polycrystalline diamond cutter. Cutting force coefficients in radial and tangential directions are calculated as a function of fiber cutting angle. The mechanistic model is shown to be capable of predicting cutting forces during milling of multidirectional CFRP laminates and capable of investigating stability of machining. © 2012 The Authors.
Open Access
A thermo-mechanical model of drill margin-borehole surface interface contact conditions in dry drilling of thick CFRP laminates
(Elsevier, 2020) Karpat, Yiğit; Karagüzel, U.; Bahtiyar, O.
Dry drilling of thick carbon fiber reinforced polymer (CFRP) laminates requires careful selection of process parameters in order to obtain acceptable borehole surface quality. Complex contact conditions between the drill margin and the borehole surface determine the integrity of the borehole surface depending on the process parameters and temperature-dependent viscoelastic material properties. Temperature rise during dry drilling reduces the elastic modulus of the CFRP and causes thermal expansion of the drill, resulting in considerable contact length at the drill margin and borehole surface interface. Manufacturers need a better understanding of the interaction among contact pressure, sliding velocity, temperature at the interface, and temperature-dependent material properties to develop predictive models for drilling CFRPs. To examine this complex interaction, this study develops a novel, hybrid model that combines a time-based analytical modeling of drilling process with a finite element-based modeling of temperature rise. Drilling experiments were performed in which thrust force, torque, and temperature were measured as a function of feed, and these measurements were used to identify unknown hybrid model parameters. The results revealed that a significant change in friction conditions occurs when increased temperatures at the margin and borehole surface interface approach and exceed the glass transition temperature of the CFRP laminate at a large feed rate. These findings show the benefit of increasing feed during dry drilling, which is nonetheless limited by the temperature-dependent material properties of the work material.