Browsing by Subject "Radio frequency"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Open Access 60 GHz wireless data center networks: A survey(Elsevier BV * North-Holland, 2021-02-11) Terzi, Çağlar; Körpeoğlu, İbrahimData centers (DCs) became an important part of computing today. A lot of services in Internet are run on DCs. Meanwhile a lot of research is done to tackle the challenges of high-performance and energy-efficient data center networking (DCN). Hot node congestion, cabling complexity/cost, and cooling cost are some of the important issues about data centers that need further investigation. Static and rigid topology in wired DCNs is an other issue that hinders flexibility. Use of wireless links for DCNs to eliminate these disadvantages is proposed and is an important research topic. In this paper, we review research studies in literature about the design of radio frequency (RF) based wireless data center networks. RF wireless DCNs can be grouped into two as hybrid (wireless and wired) and completely wireless data centers. We investigate both. We also compare wireless DCN solutions in the literature with respect to various aspects. Open areas and research ideas are also discussed.Item Open Access Analysis of current induction on thin conductors inside the body during MRI scan(Bilkent University, 2014) Açıkel, VolkanThe aim of this thesis is to develop a method to analyze currents on thin conductor structures inside the body during Magnetic Resonance Imaging (MRI) scan based on Modified Transmission Line Method (MoTLiM). In this thesis, first, Active Implantable Medical Devices (AIMDs) are modeled and the tissue heating problem, which is a result of coupling between AIMD and incident Radio Frequency (RF) fields, is examined. Then, usage of MoTLiM to analyze the currents on the guidewires is shown by solving currents on guidewire when a toroidal transmit receive coil is used with guidewire. At first, a method to measure MoTLiM parameters of leads using a network analyzer is shown. Then, IPG case and electrode are modeled with a voltage source and impedance. Values of these parameters are found using the Modi- fied Transmission Line Method (MoTLiM) and the Methods of Moments (MoM) simulations. Once the parameter values of an electrode/IPG case model are determined, they can be connected to any lead, and tip heating can be analyzed. To validate these models, both MoM simulations and MR experiments are used. The induced currents on the leads with the IPG case or electrode connections are solved using the proposed models and MoTLiM. These results are compared with the MoM simulations. In addition, an electrode is connected to a lead via an inductor. The dissipated power on the electrode is calculated using MoTLiM by changing the inductance and the results are compared with the specific absorption rate results that are obtained using MoM. Then, MRI experiments are conducted to test the IPG case and the electrode models. To test the IPG case, a bare lead is connected to the case and placed inside a uniform phantom. During a MRI scan the temperature rise at the lead is measured by changing the lead length. The power at the lead tip for the same scenario is also calculated using the IPG case model and MoTLiM. Then an electrode is connected to a lead via an inductor and placed inside a uniform phantom. During a MRI scan the temperature rise at the electrode is measured by changing the inductance and compared with the dissipated power on the electrode resistance. Second, based on the similarity between currents on guidewires and transmission lines, currents on the catheter are solved with MoTLiM. Current distributions on an insulated guidewire are solved and B1 distribution along the catheter is calculated. Effect of stripping the tip on the tip visibility is analyzed. It is shown that there is an increase in the B1 at the insulation and bare guidewire boundary. Then, a characteristic impedance is defined for the guidewires and impedance seen at the point where guidewire is inserted into the body is calculated. It is shown with EM simulations that if the impedance converges to the characteristic impedance of the guidewire, tip visibility of the guidewire is lost. At last, a new method to measure electrical properties of a phantom material is proposed. This method is used for validation of the coaxial transmission line measurement (CTLM) fixture, which is designed for measurement of electrical properties of viscous phantom materials at MRI frequencies, and which is previously presented by our group. The new method depends on the phenomena of the lead tip heating inside a phantom during MRI scan. Electrical properties of a phantom are influential on the relationship between tip temperature increase and the lead length. MoTLiM is used and the relationship between the lead length and the tip temperature increase is formulated as a function of conductivity and permittivity of the phantom. By changing the lead length, the tip temperature increase is measured and the MoTLiM formulation is fitted to these data to find the electrical properties of the phantom. Afterwards the electrical properties of the phantom are measured with the CTLM fixture and the results that are obtained with both methods are compared for an error analysis. To sum, electrical models for the IPG case and electrode are suggested, and the method is proposed to determine the parameter values. The effect of the IPG case and electrode on tip heating can be predicted using the proposed theory. An analytical analysis of guidewire with toroidal transceiver is shown. This analysis is helpful for better usage and improvements of toroidal transceiver. Also, MoTLiM analysis can be extended to other MRI guidewire antennas.Item Open Access RF heating of deep brain stimulation implants during MRI in 1.2 T vertical scanners versus 1.5 T horizontal systems: a simulation study with realistic lead configurations(Institute of Electrical and Electronics Engineers, 2020) Kazemivalipour, Ehsan; Vu, J.; Lin, S.; Bhusal, B.; Nguyen, B. T.; Kirsch, J.; Elahi, B.; Rosenow, J.; Atalar, Ergin; Golestanirad, L.Patients with deep brain stimulation (DBS) implants are often denied access to magnetic resonance imaging (MRI) due to safety concerns associated with RF heating of implants. Although MR-conditional DBS devices are available, complying with manufacturer guidelines has proved to be difficult as pulse sequences that optimally visualize DBS target structures tend to have much higher specific absorption rate (SAR) of radiofrequency energy than current guidelines allow. The MR-labeling of DBS devices, as well as the majority of studies on RF heating of conductive implants have been limited to horizontal close-bore MRI scanners. Vertical MRI scanners, originally introduced as open low-field MRI systems, are now available at 1.2 T field strength, capable of high-resolution structural and functional imaging. No literature exists on DBS SAR in this class of scanners which have a 90° rotated transmit coil and thus, generate a fundamentally different electric and magnetic field distributions. Here we present a simulation study of RF heating in a cohort of forty patient-derived DBS lead models during MRI in a commercially available vertical openbore MRI system (1.2 T OASIS, Hitachi) and a standard horizontal 1.5 T birdcage coil. Simulations were performed at two major imaging landmarks representing head and chest imaging. We calculated the maximum of 0.1g-averaged SAR (0.1g-SAR Max ) around DBS lead tips when a B 1 + = 4 μT was generated on an axial plane passing through patients body. For head landmark, 0.1g-SAR Max reached 220±188 W/kg in the 1.5 T birdcage coil, but only 14±11 W/kg in the OASIS coil. For chest landmark, 0.1g-SAR Max was 24±17 W/kg in the 1.5 T birdcage coil and 3±2 W/kg in the OASIS coil. A paired two-tail t-test revealed a significant reduction in SAR with a large effect-size during head MRI (p <; 1.5×10 -8 , Cohen's d = 1.5) as well as chest MRI (p <; 6.5×10 -10 , Cohen's d = 1.7) in 1.2 T Hitachi OASIS coil compared to a standard 1.5 T birdcage transmitter. Our findings suggest that open-bore vertical scanners may offer an untapped opportunity for MRI of patients with DBS implants.