Browsing by Subject "Squeezing"

Filter results by typing the first few letters
Now showing 1 - 2 of 2
  • Thumbnail Image
    ItemOpen Access
    The effect of fluid viscoelasticity in lubricated contacts in the presence of cavitation
    (Elsevier, 2021-03-27) Gamaniel, Samuel Shari; Dini, D.; Biancofiore, Luca
    In this work we study the influence of fluid viscoelasticity on the performance of lubricated contacts in the presence of cavitation. Several studies of viscoelastic lubricants have been carried out, but none of them have considered the possibility of the presence of cavitation. To describe the effect of viscoelasticity, we use the Oldroyd-B model. By assuming that the product between ϵ, i.e. the ratio between vertical and horizontal length scales, and the Weissenberg number (Wi), i.e. the ratio between polymer relaxation time and flow time scale, is small, we can linearise the viscoelastic thin film equations, following the approach pioneered by "Tichy, J., 1996, Non-Newtonian lubrication with the convected Maxwell model." Consequently, the zeroth-order in ϵWi corresponds to a Reynolds equation modified to describe also the film cavitation through the mass-conserving Elrod-Adams model. We consider the flow of viscoelastic lubricants using: (i) a cosine profile representing a journal bearing unwrapped geometry, and (ii) a pocketed profile to model a textured surface in lubricated contacts. The introduction of viscoelasticity decreases the length of cavitated region in the cosine profile due to the increasing pressure distribution within the film. Consequently, the load carrying capacity increases with Wi by up to 50% in the most favorable condition, confirming the beneficial influence of the polymers in bearings. On the other hand for the pocketed profile, results show that the load can increase or decrease at higher Wi depending on the texture position in the contact. The squeeze flow problem between two plates is also modeled for viscoelastic lubricants considering an oscillating top surface. For this configuration a load reduction is observed with increasing Wi due to the additional time needed to reform the film at high Wi. Furthermore, if viscoelastic effects increase, the cavitation region widens until reaching a value of Wi for which a full-film reformation does not occur after the initial film rupture.
  • Thumbnail Image
    ItemOpen Access
    Viscoelastic effects in lubricated contacts in the presence of cavitation
    (2020-11) Gamaniel, Samuel Shari
    A model is proposed to study the influence of fluid viscoelasticity on the performance of lubricated contacts in the presence of cavitation. Previous studies on viscoelastic lubricants did not consider the presence of cavitation, rather reported negative pressures in regions where cavitation was expected to occur. The proposed model uses the Oldroyd-B constitutive model to describe the presence of cavitation and assumes that the Deborah number (De), the ratio between polymer relaxation time and flow time scale, is small. In doing so, the viscoelastic thin film equations can be linearised in a similar approach to what was pioneered by ”Tichy, J., 1996, Non-Newtonian lubrication with the convected Maxwell model.” The zeroth order solution in De corresponds to the Reynolds equation and has been modified to describe also the film cavitation through the mass-conserving Elrod-Adams model. We model several bearing configurations for the flow of viscoelastic lubricants using (i) a cosine/parabolic profile representing a journal bearing unwrapped geometry, and (ii) a pocketed profile to model a textured surface in lubricated contacts. Introducing viscoelasticity to the cavitating journal bearing decreases the length of the non-active (cavitation) region due to an increasing pressure distribution in the lubricant film. This results in an increase to the load carrying capacity with increasing De corroborating the beneficial influence of the polymers in fluid film bearings. The pocket profile is shown to either increase or decrease the load carrying capacity with increasing viscoelastic effects, depending on the location of surface texturing at the contact. An oscillating squeeze flow problem is modeled for viscoelastic lubricants between two flat plates with motion only at the top surface. A reduction in the load carrying capacity at larger values of De is observed as film reformation is seen to be retarded with increasing viscoelastic effects. As viscoelastic effects become stronger, the nonactive region is grows continuously until reaching a value of De beyond which a full film reformation does not occur upon the inception of cavitation. The study is extended to a direct numerical simulations using the openFoam toolbox. A model that couples a solver for incompressible, isothermal, two phase flow with interaction between the phases and a solver for viscoelastic fluids is proposed. However, DNS are only valid for lower values of De as instabilities occur as a result of the non-linear coupling.