Browsing by Author "Biswas, R."
Now showing 1 - 9 of 9
Results Per Page
Sort Options
Item Open Access Exceptionally directional sources with photonic-bandgap crystals(Optical Society of America, 2001-11) Biswas, R.; Özbay, Ekmel; Temelkuran, B.; Bayındır, Mehmet; Sigalas, M. M.; Ho, K.-M.Three-dimensional photonic-bandgap crystals are used to design and fabricate uniquely directional sources and receivers. By utilizing the resonances of a Fabry-Perot cavity formed with photonic-bandgap crystals, we were able to create exceptionally directional sources by placing the sources within such a cavity. Very good agreement between finite-difference time-domain calculations and the experiment is obtained. Radiation patterns with half-power beam widths of less than 12 degrees were obtained. (C) 2001 Optical Society of America.Item Open Access Experimental demonstration of highly confined photonic crystal based waveguides(IEEE, 2001) Bayındır, Mehmet; Özbay, Ekmel; Temelkuran, B.; Sigalas, M. M.; Soukoulis, C. M.; Biswas, R.; Ho, K. M.The bending and guiding of the electromagnetic (EM) waves in highly confined waveguides was demonstrated. The electromagnetic waves were constructed by removing a single rod from a perfect three layer-by-layer photonic crystals. A layer-by-layer dielectric photonic crystal based on square shaped alumina rods was used with center-to-center separation of 1.12 cm. The results suggested the use of the layer-by-layer photonic crystal structure in the design of optoelectronic integrated circuits.Item Open Access Guiding, bending, and splitting of electromagnetic waves in highly confined photonic crystal waveguides(American Physical Society, 2001) Bayındır, Mehmet; Özbay, Ekmel; Temelkuran, B.; Sigalas, M. M.; Soukoulis, C. M.; Biswas, R.; Ho, K. M.We have experimentally demonstrated the guiding, bending, and splitting of electromagnetic (EM) waves in highly confined waveguides built around three-dimensional layer-by-layer photonic crystals by removing a single rod. Full transmission of the EM waves was observed for straight and bended waveguides. We also investigated the power splitter structures in which the input EM power could be efficiently divided into the output waveguide ports. The experimental results, dispersion relation and photon lifetime, were analyzed with a theory based on the tight-binding photon picture. Our results provide an important tool for designing photonic crystal based optoelectronic components.Item Open Access Highly directional resonant antennas built around photonic crystals(IEEE, 1999) Özbay, Ekmel; Temelkuran, Burak; Bayındır, Mehmet; Biswas, R.; Sigalas, M. M.; Tuttle, G.; Ho, K. M.We report a photonic crystal-based resonant antenna with a very high directivity and gain. The layer-by-layer dielectric photonic crystal we used in our experiments was designed to have a three dimensional band gap with a mid-gap frequency around 12 GHz. We used the output port of a microwave network analyzer and a monopole antenna to obtain EM waves. The input port of the network analyzer and a standard gain horn antenna were used to receive the radiated EM field from the monopole antenna. The receiver was kept free to rotate around the antenna. We investigated the radiation characteristics of this monopole antenna, which was inserted into the planar defect structures built around a photonic crystal that consisted of 20 layers. The planar defect was formed by separating the 8th and 9th layers of the structure. In order to suppress the radiation in the backward direction, we intentionally chose one of the mirrors of the cavity to have a higher reflectivity (/spl sim/18-20 dB) than the front mirror.Item Open Access Laser-micromachined millimeter-wave photonic band-gap cavity structures(American Institute of Physics, 1995) Özbay, Ekmel; Tuttle, G.; McCalmont, J. S.; Sigalas, M.; Biswas, R.; Soukoulis, C. M.; Ho, K. M.We have used laser-micromachined alumina substrates to build a three-dimensional photonic band-gap crystal. The rod-based structure has a three-dimensional full photonic band gap between 90 and 100 GHz. The high resistivity of alumina results in a typical attenuation rate of 15 dB per unit cell within the band gap. By removing material, we have built defects which can be used as millimeter-wave cavity structures. The resulting quality ~Q! factors of the millimeter-wave cavity structures were as high as 1000 with a peak transmission of 10 dB below the incident signal. © 1995 American Institute of Physics.Item Open Access Microwave applications of photonic band gap structures(IEEE, 2000-10) Temelkuran, Burak; Bayındır, Mehmet; Özbay, Ekmel; Biswas, R.; Sigalas, M. M.; Tuttle, G.; Ho, K.-M.We have investigated two major applications of photonic band gap materials. We demonstrated the guiding and bending of electromagnetic waves through planar waveguides built around layer-by-layer photonic crystals. We then investigated the radiation properties of an antenna that was formed by a hybrid combination of a monopole radiation source and a cavity built around the same photonic crystal structure. © 2000 IEEE.Item Open Access Optimized dipole antennas on photonic band gap crystals(American Institute of Physics, 1995) Cheng, S. D.; Biswas, R.; Özbay, Ekmel; McCalmont, S.; Tuttle, G.; Ho, K.-M.Photonic band gap crystals have been used as a perfectly reflecting substrate for planar dipole antennas in the 12-15 GHz regime. The position, orientation, and driving frequency of the dipole antenna on the photonic band gap crystal surface, have been optimized for antenna performance and directionality. Virtually no radiated power is lost to the photonic crystal resulting in gains and radiation efficiencies larger than antennas on other conventional dielectric substrates.© 1995 American Institute of Physics.Item Open Access Photonic band gaps with layer-by-layer double-etched structures(A I P Publishing LLC, 1996-09-03) Biswas, R.; Özbay, Ekmel; Ho, K. M.Periodic layer‐by‐layer dielectric structures with full three‐dimensional photonic band gaps have been designed and fabricated. In contrast to previous layer‐by‐layer structures the rods in each successive layer are at an angle of 70.5° to each other, achieved by etching both sides of a silicon wafer. Photonic band‐structure calculations are utilized to optimize the photonic band gap by varying the structural geometry. The structure has been fabricated by double etching Si wafers producing millimeter wavephotonic band gaps between 300 and 500 GHz, in excellent agreement with band calculations. Overetching this structure produces a multiply connected geometry and increases both the size and frequency of the photonic band gap, in very good agreement with experimental measurements. This new robust double‐etched structure doubles the frequency possible from a single Si wafer, and can be scaled to produced band gaps at higher frequencies. © 1996 American Institute of PhysicsItem Open Access Photonic crystal-based resonant antenna with a very high directivity(American Institute of Physics, 2000-09-24) Temelkuran, B.; Bayındır, Mehmet; Özbay, Ekmel; Biswas, R.; Sigalas, M. M.; Tuttle, G.; Ho, K. M.We investigate the radiation properties of an antenna that was formed by a hybrid combination of a monopole radiation source and a cavity built around a dielectric layer-by-layer three-dimensional photonic crystal. We measured a maximum directivity of 310, and a power enhancement of 180 at the resonant frequency of the cavity. We observed that the antenna has a narrow bandwidth determined by the cavity, where the resonant frequency can be tuned within the band gap of the photonic crystal. The measured radiation patterns agree well with our theoretical results. (C) 2000 American Institute of Physics